For sale my Yamaha FZS600 Fazer. Good condition for year with only 18600 miles. Accesories include: MRA Vario screen, Givi topbox rack (topbox not for sale), Arrow full stainless and carbon exhaust (sounds really nice and not too loud), just balanced the carbs, power point on handlebars, bar risers fitted, heated grips, 11 months MOT and tax, alarm fitted, new battery, just had oil and filter change with full synth oil. Ready to ride away. Has had the Yamaha 14mm sprocket nut upgrade done. No test rides unles the cash is in my hand obviously. Thanks for looking. £2000 ONO.

Re previous post of vibration and whine too k this picture of clutch basket , I've not done many clutches over the years but this does not seem right , am I wrong is this normal ? If it isn't WTF caused this ? Also when clutch push rod went back in from sprocket side it reached end if travel and felt harsh like there was broken metal at the end on the side and was catching on something
Help please !!

Attached Files

Thumbnail(s)
   

Before I go and break something does the the tube with the tabs from the speedo sensor that locates into the wheel just pull out?
I realise the thing runs off magnets so last time it was off and I pulled on it gently it wanted to come out but obviously there was resistance- is this from the magnets or is it connected to something to stop it pulling out?

Hi dudes , virgin here ha ha , newby.
Just bought me a fzs600  2002  angry wasp nose cone.
I want to ditch the fairing and streetfighter .
I tried to work out the wiring and have geten nowere.
Am going small twin headlight, which wires do I pick up from the two connector block jobies which connect the fairing  also the indicators.
Has anyone worked it out .
Also willit harm the bike just ignoring the speedo, rev and the rest.
I have fitted a magnet pickup speedo thingy push bike style , which i have used before on other bikes so that sorted that out.
Thank,s

Hi folks,
Loving my new Fazer8. Anyone got any advice on suspension improvement. I've got a model without the adjustable sussy. I'm 13st and need better damping and less dive at the front. The rear just needs better damping as preload is adjustable. I can't afford new shocks would stiffer springs and heavier fork oil help and is this something a dealer could do? Any ideas on cost?
Cheers

The manual for this bike says 21 litres of fuel plus 4 for the reserve.[/size]My last bike was a suzy GS500E and the petcock had a reserve position.In the Gen 1 Thou is the something like this to switch over to reserve if you have run out of fuel?Fortunately when running out of fuel I had enough momentum to roll up to a guy shovelling dirt and woodchips into his ute and he offered me a ride to get some gas. We took turns on the shovel naturally.I have been very low before and put in 20 litres but where is that 4 I keep asking myself. By the way when I do refuel I stop the nozzle when the level hits the bottom of the tank inlet pipe.

Hi all, might as wel start another new topic for this one.... As some of you may know I bought my Fazer with a new engine hanging in it, so I fixed it up but wasn't able to do anything with the speedo yet,
The bike was originally from Europe I think... But was brought into uk and some messer slapped a very horrible and lumpy mph face on the clocks,
Now with the new engine in I have a clock in klms a lumpy face in mph and no proper mileage for new engine,

For the sake of it the bike at the min has 106025klms  :eek on clock and the new engine has about 16,000 miles

Just wondering if anyone knows which exact wire it is for the oil light in the main white junction under the tank,


Ill explain, simply I was removing the whole from fairing and the whole lot sometime ago now, but I did plug out the wire in the junction box under the tank to remove the clocks completely, when I plugged all back together I lost indicators lights dash lights fuel light, so checked the big white connector and its corroded to hell inside, half the little needles are broken or gone, so I put it back together and tightened it with a cable tie and low and behold everything works, except the oil light,

Just wondering without having to bollox round tracing wires tru the frame and loom does anyone know the exact wire?

Newly powder coated, From a 2003 Fazer,Foxeye. Bare wheel, No bearings. £40

[smg id=1054 type=preview align=center caption="fazer"]

Hey all, made a thread a while back about what to look out for in a second hand fazer.. But seems as I didn't own one yet I thought I'd wait for introductions till I did.

Greetings from Manchester-ish!  Spent my first day on my 1999 FZS600 today and... Wow, it is an amazing machine, nice and predictable, then a bit of a beast past 7k revs. It's been complete blast so far! Hope to come for a ride with some of you guys some time, and fingers crossed I won't be hitting this place too often for help fixing the thing.