This is embarrassing to admit but purely out of interest I had a look at the 600 wiring diagram (because that's how boring I am :lol ). I marked in all the power wires in red and grounds in blue. I've done the whole loom except the wires associated with the ignition advance. I'm not sure what's happening between the pickup coil, tps and speedo sensor. I could have a stab at it but I'm not 100% sure so I was wondering if anyone could explain those components and the signals they send out?

The wiring diagram I'm looking at is on the last page of this manual http://foc-u.co.uk/index.php?action=down...iew;down=8
And I'm looking at the wires in and out of components 14, 15 and 17.

Hi guys, first post here. I've had a search but I can't find the cure for my clutch slip.


When I bough the bike it slipped a bit. Adjusting the cable didn't help much but adjusting the rod on the other end of the engine did. But it would occasionally still slip at high rpm in the higher gears.


I bit the bullet and ordered new springs, friction plates and gasket. Fitted earlier on and it all went to plan until I came to adjust the clutch. I tightened the bottom adjuster then slackened it quarter turn as per the instructions. Then adjusting the lever needed almost all of my adjustment to get it right with a few mm of play. But pulling away it's slipping really bad to the point I could probably keep it in first and hold it still with the clutch released.


I've tried adjusting the bottom adjuster tighter and looser but still can't get it right.


Anyone have any ideas?


Thanks, Carl

Fazer 1000 Gen 1
Wanted for internal part, (damper rod) from fork lower. condition of upper leg doesn't matter. Either left or right fork leg. Thank you.

2005 Gen 1 Fazer 1000 for sale. Llava red and black, 12700 miles, 2 owners, all original paperwork and books , 2 original keys, completely standard apart from fenda extenda, Yamaha bellypan , hugger, renthal ultra lows with  RG end weights (original bars and weights supplied) all fitted by me. Serviced when I bought it (March) by BikerDean in Coleford including an Exup. strip and lube) Lovely condition for its age. Front tyre 80% worn ( I reckon about 1000 miles left in it), rear 20% worn (done 1500miles), all other consumables are fine, MOT 03  March 2018. haynes manual. Purchased by me  100% standard and I've done  approx. 1500 miles and spent a few quid but having to give up biking temporarily (I hope) so going down to one bike in the garage (a Fox-eye 600).
£2750 Fixed price, no offers please - 2 similar  2005 year & condition bikes for sale are £3100 private and £3500 in a garage. Pm me to swap phone numbers if interested so we can have a chat, old fashioned I know, and I can send any pictures. Bike is in County Durham. Free cup of coffee and custard cream if you buy my bike.

Attached Files

Thumbnail(s)
   

Hi guys,


Kind of on the scrounge a little bit. I'm the main child minder during holidays & don't drive. The nipper is big & sensible enough to go on the bike, I've got her all the right gear but I want to put a top box on so she has something to lean against. Got a box but no rack for the bike. It a 600FZS 1998.


Does anyone have a spare kicking about they'd be willing to donate, or going real cheap since I'm practically broke right now.


Any help would be appreciated
Thanks guys
Ian

Hi all,


Next question - my speedo isn't working.  Can someone point me in the direction of the pickup please? 

I've got a first registered 2004, but 2003 build year FZ6 I believe and the speedo has stopped working, would this model have the front wheel rotator sensor that the lugs snap off on or am I into an ECU fault!?
Any help appreciated!
Thanks

Hi guys i just bought a 2003 fazer 600 at the moment its a none runner due to being under a cover for three years its silver and the owner said that it had blown over in the wind once so fairing has been damaged if anyone has one i would be interested in it also is it ok to fit a 120 section front tyre ?

Hi I met up with a friend who has the exact same bike as me and I was amazed at how much smoother and quieter his engine was, I don't know what to do to mine to make it sound so good. Mine "chugs" a bit on tickover and there is a rattle coming from below the camshaft. The thing is, mines only done 10,000 miles and his has done over 40k. I know my carb rubbers were replaced last year. Regular oil changes etc. Standard exhaust (he has aftermarket sports)
Sorry if this seems a dumb question, hoping someone has had the same problem.

Ghostcat

Mates Fazer: https://youtu.be/9aHeQv3jjEY

My Fazer : https://youtu.be/JLelEU8_MlI

This topic has been moved to FZS600 Fazer.

[iurl]http://foc-u.co.uk/index.php?topic=22889.0[/iurl]