Hi all,
Took alternator housing off for a re-paint. Had to remove the bobbin to release the casing. All good except that I found a small cylinder that dropped out from Lord knows where and was wondering if anyone knows what it is/where it belongs.

Attached Files

Thumbnail(s)
   

Hi, all

Don't know if you have any French members I'm an expat living in Burgundy but joined FOC UK as it seems to have a good following and some interesting posts. And life' is always easier when it's in your mother tongue!

Recently joined as have a acquired a '98 Fazer 600 in pretty good nick. Will be tinkering with rather than restoring as it has been well loved but will undoubtedly be looking for tips and advice.

Camarade ✊?

Morning all,


My wife owns a Fazer 400, frame 4YR004547, engine 4YR003740. When I'm searching for parts, all I seem to find are 4YR1 and 4YR3 designations. Is hers a Japanese-only version, perhaps? Will the parts be interchangeable?


Anyway, I'm looking for some carb parts, specifically;
diaphragms and the T connectors


If anyone has some sitting in their garage or knows of where I might find them, I'd be eternally grateful. Need to get the wife's bike back on the road before she kills me!  :eek


Cheers.
Martin

Hello to all members, I will soon be posting some parts from my father’s gen 1 Fazer 1000.
Hope they go to enthusiasts.

Just one week to go till the London Fight Motorcycle Theft meeting. 

This is your best opportunity to get answers to your questions from a senior MET Police Officer, the London Deputy Mayor for Policing and Crime, Sophie Linden, and CEO of the MCIA, Tony Campbell.

Make sure you book your FREE ticket to attend in person or online before they all go (numbers are limited). Book tickets here: https://www.eventbrite.co.uk/e/london-fi...7072164107

Attached Files

  13946833825631986102.jpg (Size: 20.58 KB / Downloads: 14)

https://youtu.be/NjJfygRV0JI

Morning all, 
I need to change the cam chain tensioner due to the rattle that I have.
I have watched a few YouTube videos.  Most say to put the engine in top dead centre before removing the cam tensioner.
I read the Haynes manual and it just said to take it out.  No mention of putting the engine in TDC
I have read some forums and haven't seen anyone mention putting it in TDC


What is everyone's thoughts? 


Cheers

Hey all, so I've been looking through some of the old posts to do with the same issue I'm having - no spark - and I think I've narrowed down the problem but have a couple of questions.


1. the initial clicking/ticking you hear when the key is turned (button NOT pressed), is this the starter circuit cut off/fuel pump relay?


2. testing resistance on the ignition coils - primary - the Haynes manual states the reading should be between 1.87 - 2.53ohm. I'm getting 3.5 on both coils and according to the book, they need replacing but I've seen a few people saying that reading is ok?


3. what is the most likely cause of no spark? I don't have the funds to start replacing loads of bits.
I have checked:
battery is charged and holding full charge;
new plugs;
plug caps and coils HT leads are testing fine;
fuses are all good;
earths are good as far as I can tell;
starter motor is turning over and solenoid is clicking as it should;
pick up coil is fine (even though the manual gives the wrong colour wires!);
checked connector blocks and all seem fine - no corrosion and tightly connected.


I'm about to test continuity on pretty much everything and carry out the tests for the starter cut off/fuel pump relay as per the book but I think it's that that is causing the problem (very limited knowledge but logically thinking...)


Sorry it's a lot to take in but I'm sure it's something simple I'm missing


All lights on dash are n, horn and lights work and engine turns over.


Cheers.....anyone!

Hi hello and howdy.


Recently joined, had a 02 600fzs for nearly a year now.
I'm in Bristol and don't get to ride as much as I should - cos bikes got issues!..


I'm hoping some can help me get the problem solved as cheaply and as easily as possible.


Unfortunately Im not a font of knowledge but I'll hang out and have a go as much as I can.


Cheeries

So I will be down there helping out on the MAG stand on Saturday/Sunday, any of you herberts gonna come down..?