Greetings from the Emerald Isle.


Just bought my Fazer 1000 love it but the exup valve us seized solid still seams to go OK should I fix it or remove it will it make a massive difference as its shagged anyway?

Hi Fellow Foc-ers! (Is that alright to say?!)

So I have been using your info for the past few week helping me rebuild a 2001 FZS600 that had been off the road for 5 years.

It’s been a fantastic learning curve so far, but now I’m struggling…

It doesn’t like being in a low rpm and pulling away.

1st gear pulls away okay and the engine seems happy,
2nd gear, below 3,500rpm it judders quite viciously,
3rd, 4th, 5th, 6th, it bogs down below 5000rpm.

It would likely judder in the higher gears at a lower rpm, but I wouldn’t be in them at any low speed.

It doesn’t Idle without the idle adjust screw/butterflies opened a bit, but even then at 1250rpm it surges every couple of seconds.
Pilot adjust screws are set at 2 turns, though have tried at 1.5 turns and 2.5 turns which don’t make too much difference to idle speed.

Above 5000rpm the engine really sings now, and pulls constantly well especially after the work I’ve done below (previously it even bogged down at 7-8000 rpm), but none of the jobs have rectified the low speed rpm judder.

The clutch does seem to make a chatter on idle.

It does smell like a rich mix on idle, I.e too much fuel?

Soooo,

Following reason other people’s advise on here,

I have stripped the carbs,
cleaned/rebuilt/balanced/jets cleared/all pipes flushed. (Balanced visually when carbs removed and with a 4way vacuum gauge)
New orings fitted on main jet and float needle and float needle valve (remembered the 4 little screws hold the valves)
Fitted new air filter (though not k&n)
Fitted new iridium spark plugs even though originals were brown and gapped well.
Replaced cracked carb/engine rubbers
Emptied as flushed fuel tank.
Checked caps for sparking and they do all spark well or at least sound like they do, and don’t arc in the dark.

I have a new fuel pump (not yet fitted) as I thought it was fuel supply when it bogged down under high rpm.

What have I missed? Fuel/air mix? Float level? Clutch issues?

Any help would be greatly appreciated as the bike is fab, just not round town and don’t wanna have people look down on the Fazer as I rev the nuts off it and feather the clutch at 25mph through town trying to stop the judder!

Many thanks!!

This is an important message for all posters on these Forums.

We want to make these Forums a friendly, welcoming and open place for people to discuss bikes, biking and bike related issues.

Discussions of political topics are allowed, however, please keep them to separate threads as much as possible. If a bike related topic starts getting political, we may curtail the discussion or split it off into a thread of its own to keep the main topic from being swamped.

We appreciate that feelings can run high on some issues, however before you respond to a comment which you don't like or don't agree with, we would be grateful if you would pause for a moment, take a step back and consider whether "popping off" at someone else is going to add anything positive to the discussion.

There is no problem with you disagreeing with someone, but while "I don't think you're correct because..." is acceptable "you're an idiot" is not.

Personal attacks, insults, bullying or discriminatory language etc will not be tolerated and posts may be edited or removed at the Moderators' discretion.

Violations of these rules or other disruptive behaviour may result in a member's posting privileges being temporarily restricted.

Continued violations or other unacceptable behaviour may result in a member being permanantly banned.

Please note that if you have an issue with a poster or a post, use the "Report to Moderator" link at the bottom right hand corner of each post, do not post comments in the thread or call out other people's actions.

Moderator decisions are final and are not open to discussion.

- The Moderation Team

Hello


I need some room in the garage so am looking to sell my black 2001 fzs600

• I’ve owned it since 2018, currently around 42000 miles. MOT Valid until October. It’s been serviced in the last 500 miles. Brand new PR4 tires fitted 2000 miles ago, along with new braided brake lines on the front, new pads on the front, new chain and sprockets (standard gearing). Also put a new battery in it a month ago.
  
• USB power fitted with the output on the bars. Also has a quadlock mount fitted which can go with the bike if wanted.
  
• It’s got a small crack to the front fairing and a few small scratches on the top of the tank caused by grit getting under magentic pad of an old tank bag. Other than that it’s a tidy bike.
  
• It’s currently registered on a private plate, but will not be sold with the bike.
  
• I also stuck a beer clutch pack in her last summer, so less than 2000 miles on the clutch too.
  
• Located near Milton Keynes.
  
• Metzeler roadtecs were on when photos taken, now has Michelin PR4s.
  

Attached Files

Thumbnail(s)
           

Hello, today i finally got my fazer on the dyno after i ivanized it. The guy claims that it runs way to rich. He's saying that i need to get the idle jet 5 sizes smaller, the main jet 10 sized smaller and put the clips on the needles 1 step higher so the needle gets lower.
Can someone help me out here, i've done everything the way ivan described it.

Attached Files

Thumbnail(s)
   

Hey guys ,


Selling my 1999 fzs600 in black


Only selling as I was left a red 1998 fzs600 to me in a friend's will


Check it out on eBay


https://www.ebay.co.uk/itm/Yamaha-FZS-60...890.l49286

[Edited to fix the link appearing in a miniscule font. GrahamM - Moderator

Hi


I require a set of pillion grab rails in black or dark silver to fit a 04 fazer thou

Hi

I have for sale the following parts for a FZS1000:

• Standard Rear shock with less than 5k usage
  
• Standard Front Fork Springs with less than 5k usage
  
• Standard Exhaust
  
• Standard Levers
  
• Standard Black Handlebar
  
• Standard Bar Ends
  

Admin pls delete.


Hi Peeps.


I'm on the hunt for a mint pair of 43mm Fazer 1000 stanchions.
I'm near Barnsley S/Yorkshire,  so if any of u fine Foccers have a pair not in use, I'd be interested if not too far away from me & the price is right.
I would prefer to view & collect.
Obviously they must be straight & free from pitting.
I will consider complete forks, but I only need stanchions for my rebuild & it's not easy to see a bent stanchion on a complete fork leg.




I would like at some point to upgrade the front end to R1 spec, funds don't allow at this time  :'(


Rgds
Gaz

Hi all,
as title says Im looking for Stock linkage dogbone for FZ1S (2009). Recently I got myself a Fazer and it is lowered too much, it is unacceptible for me plus it is very hard on the road. I dont feel safe driving it, no fun at all.
Maybe someone has it somewhere hidden or wants to get rid of it?
Part 24 on here: https://ie.fowlersparts.co.uk/parts/6451...c/rear-arm
Thank you.