| Welcome, Guest |
You have to register before you can post on our site.
|
| Forum Statistics |
» Members: 7,951
» Latest member: drcell
» Forum threads: 28,228
» Forum posts: 329,168
Full Statistics
|
| Online Users |
There are currently 867 online users. » 0 Member(s) | 863 Guest(s) Applebot, Google, SemrushBot, ai.
|
| Latest Threads |
Whoever posts last is bes...
Forum: General
Last Post: robbo
6 hours ago
» Replies: 1,739
» Views: 514,096
|
Gen 1 suspension upgrades
Forum: Fazer 1000/FZ1 corner
Last Post: b1k3rdude
Yesterday, 08:20 AM
» Replies: 1
» Views: 32
|
Carpal Tunnel Syndrome
Forum: General
Last Post: robbo
28-02-26, 11:29 AM
» Replies: 68
» Views: 23,360
|
FZS1000 valve check
Forum: Fazer 1000/FZ1 corner
Last Post: PieEater
26-02-26, 02:59 PM
» Replies: 1
» Views: 86
|
BEST FAZER FOR SALE
Forum: For Sale & Wanted
Last Post: Greg13
25-02-26, 03:47 PM
» Replies: 4
» Views: 742
|
Who doesn't love a bit of...
Forum: Fazer 1000/FZ1 corner
Last Post: RMT1983
24-02-26, 11:24 PM
» Replies: 23
» Views: 1,717
|
FZS1000 headers
Forum: Fazer 1000/FZ1 corner
Last Post: RMT1983
24-02-26, 11:22 PM
» Replies: 1
» Views: 63
|
Scottoiler gone bad?
Forum: General
Last Post: Slaninar
23-02-26, 05:16 PM
» Replies: 16
» Views: 1,684
|
Cam chain tensioner
Forum: Fazer 1000/FZ1 corner
Last Post: robbo
23-02-26, 10:38 AM
» Replies: 1
» Views: 55
|
New here
Forum: General
Last Post: robbo
20-02-26, 11:13 AM
» Replies: 5
» Views: 179
|
|
|
| Gen 1 standard fuelling |
|
Posted by: JayB - 11-12-12, 06:00 PM - Forum: Fazer 1000/FZ1 corner
- Replies (13)
|
 |
Guys, before we start, I can;t afford to Ivanise the bike at the moment, I know it's highly recommended, but if anyone else hasn't done theirs yet....... :lol can they comment on the standard fuelling.
I am just wondering if the set-up is to blame or something peculiar with my bike.
It seems to be a little bogged down, say when you are pulling out of a junction or filtering, you slip the clutch away and have to give it more right wrist than it feels like you should, then the bike catches up and surges away from you a little....?
Has given me a few little worries now and again, but I've mainly had fuel injected bikes lately.
I think I need to get the carbs balanced, but not sure if that will cure it, it doesn't really hunt around at a set speed but it does feel a little flat sometimes.
Mike (Falcon) suggested doing the O rings and at the same adjusting the pilot screws slightly, can I get to them without removing carbs when I balance them?
I had a couple of ZX9Rs and they were terrible, if you were in a medium gear, rolled off and then back on, say overtaking a series of cars, there would be a delay then they would shoot off, cured by setting the pilot screws further in I think it was... is this a similar thing with the original jetting of the Fazer?
Until I can afford to mess, I would like to optimise it as best I can.
|
|
|
| Anodised brake and clutch levers for FZS 600 |
|
Posted by: CharlieDee - 11-12-12, 03:40 PM - Forum: FZS600 Fazer
- Replies (2)
|
 |
Afternoon Foccers,
I have been looking online for some anodised levers for my 03 FZS 600 and I am struggling in finding any specific for my bike.... can anyone point me in the right direction or even recommend some?? would be most appreciated!! Charlie.
|
|
|
| How Cold is too cold? |
|
Posted by: flesh - 10-12-12, 11:45 PM - Forum: General
- Replies (39)
|
 |
As I wheeled the bike out of the garage for the first time in a week (due to the street being iced over) and looked at the -1 on the thermometer I wondered how cold is too cold.
Fair enough about snow, as riding a bike in those conditions is just daft, but how cold would you go?
|
|
|
|