This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Topics - popeye72
Pages: [1]
1
« on: 24 April 2013, 03:44:57 pm »
anyone going tonight 
2
« on: 19 April 2013, 09:45:31 am »
traded in my fazer for a sprint, sorry to see the old girl go but the sprint is something else  
3
« on: 18 April 2013, 12:20:29 pm »
whats your views, i know the v system has its pros and cons but i have recently bought the e system and so far its purfek, no excess oil switches off at low speed or in traffic temp gauge and easier to install, but price 
4
« on: 16 April 2013, 11:39:20 am »
anyone going tonight 
5
« on: 10 April 2013, 03:37:43 pm »
for sale only two months old and used just once, this is the pro version in the protective case. i Bought this to ballance carbs on my 2003 fzs 600 which has now been sold and wont need it for the sprint. sensible offers, i am in Southampton so anyone local let me know 
6
« on: 14 March 2013, 04:42:47 pm »
hello guys and girls, i posted a thread in general about purchasing a Triumph sprint, however i am test ridding a Gen 2 this weekend. Any help tips or things to look out for would be good its a 2008 model
7
« on: 11 March 2013, 09:12:24 pm »
I know it's not a fazer but I have had a square and foxeye 600 and want to try something different so would like your honest opinions I can afford a 2008 model
8
« on: 11 March 2013, 04:22:26 pm »
ok gurus, i have flush fit front indicators, fitted when i bought the bike. front right bulb blew and i couldnt find a direct replacement, its a 12v 23/8w it has staggerd baynets and they are not 180 degrees apart, if that makes sense. i cant find them anywhere i fitted a small 12v 10w orange indicator bulb that works for about 3 flashes then both front and back flash fast??? if i put hazards on they all flash normal, left hand indcators flash ok, when i moved the lamp to the other side it happened there so definatly the bulb. i know its the bulb but cannot find one??? 
9
« on: 08 March 2013, 04:47:53 pm »
ok silly question time, what is the port or hole for half way up the fins and in the middle? there is one either side i may be being paranoid but im sure im getting water leaking from these holes ????
10
« on: 06 March 2013, 03:05:50 pm »
ok ballanced the carbs today first time so a good experience however the manual states vacuum readings of 23-25 but i was getting 18-19 on fast tick over  is this good or bad cus i havent a clue any help would be great
11
« on: 05 March 2013, 09:19:17 am »
Morning guys and girls, firstly i need to appologise to the london foccers as couldnt make sunday due to the above  i recently changed my front brake lines ( braided ) and piston seals, after cleaning my rear brake pistons and found they needed changing i thought i would look at the front and clean them up. on piston would not retract, i could get it to push out but really struggled to push it back in. I removed the piston cleaned everything thouroughly and yet it still is ALMOST impossible to push all the way home. it will go passed the dust seal but when it gets to the oil seal stops. so inspected again and the only thing i can see is the seal looks as if it is not seated properly but it is very hard to tell. removed seal and reseated but still looks the same as if back edge is slightly raised. anyway new seal ordered, but has anyone had this before. i have renewed master cylinder seals and all other pistons move freely. also how much pressure would you expect to use to push the piston back????? thanks in advance
12
« on: 27 February 2013, 10:47:34 am »
woo hoo, morgan carbtune just arrived!!! recently bought fuel filter , plugs , air filter cleaning kit and BLUE engine casing bolt kit, not sure on the look yet but now rear caliper siezing so off the road until i can fix that and then balance the carbs. just thought i would share  
13
« on: 18 February 2013, 10:06:39 am »
jsut asking you though5ts on pro-bolt kits ? are they any good alluminium engine casing is what i am looking for??
14
« on: 04 February 2013, 12:44:57 pm »
been looking for a while and i know a few have mentioned a Hampshire meet, any suggestions guys or have i already missed any meets, i have been going to Micks burger bar Portsmouth but wondered if there is anything closer to Southampton
15
« on: 04 February 2013, 11:36:39 am »
Hi Guys and girls, have noticed my foxeye has begun to tick over fast for about twenty seconds after pulling up to lights etc, it runs at about 1500 rpm and then without me doing anything settles back to around 1000 rpm after about twenty seconds!!!! strange any ideas from the gurus???
16
« on: 29 January 2013, 02:11:41 pm »
not all of the home page is loading, has anyone else had this problem. Obviuosly i can get to forums etc but where the new post section is well its not???
17
« on: 08 November 2012, 02:53:31 pm »
hi guys and girls has anyone checked oil pressure before? and if so where do you get the attachements?
18
« on: 28 September 2012, 02:40:54 pm »
just thought i would brag about recieving new Hellbrake lines, piston seals and mastyer cylinder kit today parts from WEMOTO and YAMBITS all supplied quickly without incident, well we all like to moan when it goes bad so just thought i would mention good service
19
« on: 17 September 2012, 03:12:37 pm »
just getting your opinions on sports set up or standard fornt brake lines pro's and cons pleeeease
20
« on: 12 September 2012, 03:21:40 pm »
guys i know its on here but cant find it, looking to have my seat re-modelled or replaced any suggestions its a 2003
21
« on: 06 September 2012, 04:46:59 pm »
hey guys trying to get fzs 600 haynes manual from downlaods area but not working any ideas
Pages: [1]
|
Show Posts
