Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
fitting soft panniers fz6
#1
hi all,
ive got what looks like oxford first time bike panniers any hints on fitting them as i will be taking a pillion passenger as well

thanks
david
Reply
#2
I've got them Smile
middle connecting strap - under seat
two other connecting strap- over seat
other straps I did one on each side to the pillion footpegs and the ones at the back I joined to each other.

My gf didn't notice any difference with the seat straps on or off because of the trousers she was wearing Smile

Hope that helps...

Although I've just noticed it's for an FZ6, I'm on an FZS1000, but I would say it's all the same Smile

except watch out for your underseat exhausts Smile
Reply
#3
I have them as well. On my FZS600 I put all 3 straps under the seat so it doesn't make it uncomfortable for my missus. Don't need her moaning any more than usual  :lol
Reply
#4
cheers will do a conglomeration of both when i finished daughters bedroom painting  :'(
Reply
#5
I have an FZ6 and soft luggage and no problem with the underseat exhaust as the heat sheilds really work
Greybeard now 
Reply
#6
(16-03-12, 11:05 PM)dolau link Wrote: I have an FZ6 and soft luggage and no problem with the underseat exhaust as the heat sheilds really work

Does it secure to eg the pillion footpeg mounts? I looked at soft luggage for my FZ6 but I was worried it might foul the rear wheel.
Reply
#7
Nope- always put my cross webbing under the seat- makes it less prone to nicking

There seemed to be plenty of places to put bingees when I did it last

Off this weekend to Devon for four days on the bike so will remind myself how to do it- maybe put a picture up
Greybeard now 
Reply
#8
well i secured it did over/under velcro on seat then bungee from back to footrest,then adjutable webbing underneathexhaust wheel arch, then adjustable webbing either side to footrest stayed in place but got well dirty with mud and crud gonna see if theres a way to stop mud comming out as girlfriends back was all covered tooSad
Reply
#9
[Image: IMG_0333.jpg]

Slipped the straps under the seat and over the front grab rails- dont think I will need the bungees and straps as well but will see when I am fully loaded in the morning.... looks like good weather for a tour of Devon for four days with No1 son!
Greybeard now 
Reply
#10
Out of interest, could you show a side-on/ back view if you have time?
Reply
#11
looks to me from your pic that the plastic push clips are gonna rub your grab rails on the front ,
the bottom bungees and straps are so the bottom of the bags dont jump around
Reply
#12
Didnt move an inch.

Didnt use bungees it was tight with the straps under the seat and I ran the pull up webbing over the grab rail to pull them up tight

They rested on the rubber anti slip matting on the exhausts and the heat shields got hot but not enough to cause any damage and they were fully laden.

Will try and upload a picture of them fitted in touring mode.

Also I have the Givi waterproof satvan bag which I fitted to the handlebar yoke with a 12v socket in the fairing side panels near the front. Worked a treat and could see the satnav over my tank bag but had to lose my camera mount which is usually in that position.

No chaffing on the bodywork... only mine in leathers with so much sunshine.... but that is another story  :o
Greybeard now 
Reply
#13
I use Oxford Sports panniers and the are great, they touch my Scorpion exhaust but its not a problem
Reply
#14
These panniers look very good, especially the price Amazon are selling them for.


How about security though? I assume there is no way of locking the compartments. I would not like to leave my helmet in one if it could be opened easily. Look great for just carrying stuff from one place to another though.
[Image: 147329.png]
Reply
#15
had these on my fzs1000....worked a treat  Big Grin ......i protected the bodywork with some rubber gauze matting , £1 from the pound shop....bargain  Big Grin
One, is never going to be enough.....
Reply


Forum Jump:


Users browsing this thread: