Post by: slimwilly on 07 February 2015, 08:49:42 pm
Post by: noggythenog on 07 February 2015, 08:58:45 pm
Fork off slim you sarky forker :lol
Post by: unfazed on 07 February 2015, 09:08:29 pm
Post by: slimwilly on 08 February 2015, 07:02:03 am
Manual in the download section would be a good place to start :lol
Ooh,thanks,,the obvious is never that obvious to the un obvious
Post by: unfazed on 08 February 2015, 10:05:11 am
Post by: slimwilly on 23 February 2015, 04:19:54 pm
what do you do when you open the download section =doh :o
Post by: noggythenog on 23 February 2015, 04:22:58 pm
Changing fork oil is easy Slim
Just pop it into the stealers :rolleyes ...well thats what ill be doing anyway
Some things i just cannot be arsed learning.
Post by: slimwilly on 23 February 2015, 04:35:03 pm
i have serviced a few forks in days gone by,, i used to do a few Marzocchi MTB forks,upside down ones too, those had rebound and compression on both legs.
I would rather see if i can get any info first,tips,what not to do etc ,
Loads of videos on you tube, none that i see of the same forks
Post by: unfazed on 24 February 2015, 09:19:01 pm
Take note of the number of rings showing on the preload adjuster.
Unscrew the preload adjuster to full soft. (all rings showing)
With wheel and mudguard off
Loosen the top yolk pinch bolt FIRST
Loosen the fork cap nut
Loosen the lower pinch bolts
Unscrew the Cap nut completely
Compress the fork leg fully to expose the damper rod and spacer (Take a picture to assist in putting it back in the right order :) )
You may need to make up a compressor to fit the holes in the spacer to compress the spring a bit.
Use and open ended spanner to and a ring spanner on the cap nut to undo the lock nut effect of the nut on the damper rod with the adjuster, screw off the adjuster
Withdraw the inner damper rod
Measure the distance from the nut to the top of the damper rod to ensure you put it back to the same point.
Now Compress the spring to remove the nut
Remove the compressor the spacer and the spring
Drain the oil pumping the damper rod to get all the oil out.
Do one leg at the time and you won't mix up the compression and rebound adjusters, if you do decide to do both legs together do not mix them up as the adjuster and rod are different in both legs.
Post by: Smurfbud on 25 February 2015, 09:48:19 am
Post by: richfzs on 25 February 2015, 10:59:29 am
Post by: unfazed on 25 February 2015, 06:16:19 pm
Cos it compresses the fork where it clamps, stops you undoing the cap nut
:thumbup
and you could damage the threads in the cap nut or fork leg or both by forcing it when compressed by the yolk
Post by: slimwilly on 25 February 2015, 06:51:38 pm
I did it last night at about seven,,you found the notes at 9 pm,,lol
Got both legs out in half an hour no probs, having the bike lift is ace.
P1110718 |
Post by: slimwilly on 25 February 2015, 07:00:38 pm
10 |
Only takes half an hour to get the forks off.
The bike has been stood for a while and the oil at the top was very clean then soon after out came very dark aluminium filled dirty oil,left them draining all night.
There is two ways to replace the oil, after pumping them and getting the oil out and draining all night,
Option 1= check how much oil came out,volume, and replace at this stage, supposedly fine for street style riding,and any new oil is better than old oil.
Option 2= Remove top cap,springs etc and refill and measure air gap at top of forks,after pumping and compressing oil a few times, this option is a must for racers as oil height is critical in fork tuning.
Post by: slimwilly on 26 February 2015, 06:52:22 pm
Oil bought = 5w for both legs, it seems as though light weight people and as standard forks have between 2.5w and 5w oil ,
some slow the forks down with up to 10w oil in one or both legs.Perhaps if you are heavier, or huge braker,,,slow down :lol
Oil volume should be 545ml standard and air gap at stock is 3.75" and common up to 4" =110mm
Some have drained theirs and only got 470mls out,,thats if it all came out :D .
I will measure mine now in my new cheapo plastic measure jug :lol
Post by: noggythenog on 26 February 2015, 07:02:05 pm
Mind dont oberfill eithr, the k tech guys said thats maybe whats up with mine and why im not able to use all the travel even with my great mass.
Post by: slimwilly on 26 February 2015, 09:29:40 pm
i just put 500 ml back in the rebound side ,pumped the air out so cartridge is working and there is only 3" air gap,overfill slightly.
now have to ake some out to get just under 4"
I made a peach of a scrapyard spring compressor,pics in a bit :lol