Date: 01-05-24  Time: 01:43 am

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - tex

Pages: 1 ... 26 27 [28]
676
For Sale & Wanted / Re: WANTED front brake lever
« on: 08 May 2012, 08:53:03 pm »
 
For a fazer 1000 gen 1, or can anyone reccommend some good replacement levers?


are the Chinese one's on fleabay any good?


TIA


John
 
 
 
  I have one in my gararge, you are welcome to it, if you pay the post.
 
                        tex

677
For Sale & Wanted / Re: Probolt titanium nuts bolts
« on: 03 May 2012, 08:51:48 pm »

dibs on the rear caliper bolts please.
 
         tex
Ok tex your names on em

    Money sent.

678
For Sale & Wanted / Re: Probolt titanium nuts bolts
« on: 02 May 2012, 08:22:40 pm »
 
dibs on the rear caliper bolts please.
 
         tex

679
 
  If i had seen this earlier i would have gone, nice round there. Where abouts are you based in herts.
 
 
                                 tex

680
Fazer 1000/FZ1 corner / Re: Mirrors with built in indicators
« on: 08 February 2012, 09:01:16 pm »
 
 I got some from busters, They work ok,£25 down from £50. they are a generic type so will fit most bikes, screws in the brake side, and you can get a bracket of ebay for the clutch side, or get a fz8 clutch bracket with the threads built in, it is a perfect fit. It does leave two holes , but you can get some block off plates, not sure where, im sure somebody will be along with a link .
 
               Tex

681
Fazer 1000/FZ1 corner / Re: fazer bearing change
« on: 20 January 2012, 08:24:02 pm »
 
Hi,
    If you speak to like, his r6 shocks are nearly new, a good buy .
 
                 Tex

682
General / Re: gauge
« on: 19 January 2012, 08:47:56 pm »
 
 Thanks paul

683
General / Re: gauge
« on: 08 January 2012, 12:33:24 pm »
 
 
  Thanks silver, the gauge came from christian, so i have the instructions. Never done anything like this ,so did not want to screw it up, can do the basics, I will have a good read and might have a go.
 
 
                             tex.

684
General / gauge
« on: 07 January 2012, 10:25:17 am »
 
 
     hi,
        Does anybody know of a good motorcycle elecy or shop, to fit a multi gauge and white dials, I live in the north london, herts essex area. But dont mind traverling a bit.
 
                  Tex

686
Introduction / Re: New member from Middlesbrough.
« on: 31 December 2011, 09:51:07 am »
 
 
 I thought you were the monkey hangers in that part of the north east!! :D  or was it hartlepool  ??, and welcome

687
General / Re: Everyone should know about Hastings Direct
« on: 29 December 2011, 09:09:16 pm »
 
I reckon 60% of people, if they went to claim, they would find they are not insured, this could be for not declaring points, or forgetting to tell their ins about a claim they have had in the past, or vehicle not up to spec, ie bald tyres.

688
General / Re: My Christmas present to me
« on: 26 December 2011, 04:48:09 pm »
Mine was to have this tatood on my right butt cheek.

http://www.famouslogos.org/the-rolling-stones-logo

 
 I did not reliase you has such good taste in music kos, One of my fav bands.

689
General / Re: Time to quit?
« on: 21 December 2011, 10:08:05 pm »
 
Its so easy to start again, i gave up for 11 years, thought i would be ok, then someone brought me a pack of cigars last xmas, that started me smoking again. must try and stop this new year!!

690
Fazer 1000/FZ1 corner / Re: Fitting new battery - am I going nuts?
« on: 09 November 2011, 09:02:46 pm »
 
 It might be one of the universal batt, check that there are not two sets of terminals.
 
                tex

691
General / Re: What was your first car ?
« on: 30 September 2011, 09:18:49 pm »
 
 1971 vauxhall victor 2.3, got it of a neighbour fast back then, but body was rotten

Pages: 1 ... 26 27 [28]