This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Topics - mars696
Pages: [1]
1
« on: 18 October 2017, 07:39:07 pm »
Hi again guys! Soooo after solving this freaking problem... http://foc-u.co.uk/index.php/topic,23230.msg267705.html#msg267705i am facing another fuel problem that was coexisting with the previous one. As i am standing at a traffic light or a crossroad or something like that,with the engine fully warmed, and i lightly blip the throttle the rpms drops significantly and come again at proper idle speed or when i try to start moving the bike feels too rich and want more throttle opening. The pilot screws are adjusted at approximately 2.5 turns (01 model), if i try to reduce this,the bike doesnt idle properly. I have tried to set the float heights in many different settings. To archive the 3.5 mm above mating surface like Yamaha suggest, i have to set the float height at approximately 15+ mm above carb surface when bench setting them,but the bike with that setting, fills very strange and wont idle properly again. Now i am at ~13.5 mm and with the tube test it reads something like ~6.5mm above mating surface.I m confused again for focs sake!  Air filter is clean,carbs are very clean, i have this problem with both carbs sets i have( spare parts!!!!), pilot jets are yamaha's 12.5. Any help or idea will be much appreciated, because i am out again... 
2
« on: 08 September 2017, 07:50:01 pm »
Hello to everyone! Sooooo, finaly after 9 focking years that i own the bike, i manage to find the problem. What was the problem,you ask. Off throttle-low rpm stuttering,jumping etc. For 9 years no mechanic could find the problem. For 9 years i have spend so many hours at removing, cleaning, checking parts again and again . Now i can remove the carbs in 15 min  So much money spend on parts that could cause the problem, buying carb synchro tools any many more,but none of them was the cause.... A week ago,i had removed the carbs for one last time to clean and check floats etc.Everything was squeaky clean. When reassembling,i overtight one pilot jet and the focking thing broke in half. Fortunately i manage to remove the half that was inside the carb slot. Cursing was unbelievable. Order 4 spare ebc pilot jets online,because there was no stock in my country.One week without the bike. While waiting for the parts, i had a funny idea to remove the diaphragms from the slides...just for the hell of it.... and BOOOOM. One focking diaphragm had a pin hole at the base,you could only see it if removed from slide,or very carefully inspected,which i had done in past,but maybe not so carefully and ofcource no mechanic had spot it. I patched it with some hi temp silicone temporarily,just to clarify if this is the cause. Finally, when pilot jets arrived, assembled, balanced,pilot screws setup and out for a test ride. YEEEEEEEEESSSSS after 9 years the bike running properly!! No hesitation,no stutering, now i can drive at low rpm speeds without slipping the clucth like crazy. Even now, i still can't believe it! Thank you guys for all the help that you gave me all these years! 
3
« on: 11 August 2017, 03:01:51 pm »
I am asking for a good set of carbs for fzs 600,my bike is 2001 model. i searh for a set ,in best working condition i can find. Its my last hope for my many years low rev shuttering bitch!  I live in Greece,anyone willing to help or point me where i can find one will be much appreciated. Thank you alot!
4
« on: 02 August 2016, 08:03:30 am »
Hi guys!
Anyone knows what's the measurement for the float bowls,with the caliper method?
From a web search i didnt find something sure,something like 13mm or 14mm.
I have now adjust them at 13mm...
Thanks,
Aris.
6
« on: 31 May 2015, 09:48:46 am »
Hi there foccers!
My front wheel has develop a strange gap-movement the last weeks...
I though it was the steering bearings,which i replaced yestreday,but thats when i realize its the wheel which moving...
The wheel bearings are also changed a year ago....its possible to need new again? Or maybe something with my spindle or my installation?
Thanks,
Aris.
7
« on: 04 October 2013, 05:23:18 pm »
Anybody knows the diameter of the coolant hose, at point before it goes to the engine(near generator)?
I want to fit a water temperature gauge,and i must fit a joint pipe for the sensor!
Is this a good place to install the sensor?
Thanks!
8
« on: 15 August 2013, 09:53:25 am »
I took out my carbs yesterday,to adjust the float heights,because of a long time idle-3k rpm stutter.
I find it realy hard to adjust them with the clear hose method...
I adjust them(at least i thought) and put carbs back in.......and guess what.....The bike runs like *@$#$@
It didnt improve the low stutter,and now the engine refuse to go over 6-7 rpm with load.....
I have done everything 9-10 months i am searching for the problem,EVERYTHING i have read here:plugs, plugs caps,carb cleaning,testing coils,tps and much more...
I am so sick of this....
9
« on: 13 July 2013, 02:55:34 pm »
I found that i have coolant leaking from the thermostat.
Coolant leaking exactly from the under bolt that hold the the thermostat housing.
So anyone had the same problem?
My mind goes to the o-ring between those parts...but where i can find one....
10
« on: 09 July 2013, 02:29:39 am »
Hi focs!After buying and installing a new gauge with temperature bar gauge,i try to connect it with the engine temperature sensor, at the thermostat(the one with only one plug),but i dont get any readings.As i check the manual,it refers to it like a "switch",so i think, that it only trigger the warning led ,under certain temperature.Correct if i am wrong. So i am looking for a proper water sensor and i would like to know what the sensors threads are? Anybody??Thanks!!!
11
« on: 14 June 2013, 09:26:40 am »
Hi focs! Want to sell: 1)Fzs 600 clocks,form a perfect running 2001 model,with 48.000 km. Its in perfect condition,with only an slight superficial crack ok the back,but it works perfect.(look photos). Price:65 GBP +shipping(from Greece)  
2)Fzs 600 headlights,from the same bike.
Works perfectly,it only has a crack at the upper left holder,but it fits and holds nice and tightly.
Price:60GBP+shipping(from Greece)
 
3)41mm clip ons from an suzuki sv,fits perfectly to our lovely fazer 98-03.
Price:35GBP+shipping (from Greece)
 
As i allready mention,all parts are in Greece,so if you want something,please contact me to ask about the exact shipping rates for your place.
All shipping will be with tracking number ofcource.
Payment only via paypal please.
For ANYTHING you want,please dont hesitate to contact me! 
Thanks,
Aris.
12
« on: 06 March 2013, 09:11:37 am »
Hi focs
Does anyone know the size/number of the wheel bearings(front and rear)?
I want to buy them ftom a hardware store to avoid yamahas price!
Thank you!
13
« on: 21 August 2012, 07:36:22 am »
Hi again focs! I have a low rev stuttering.beneath 3000 rpm,starts from idle. If i hold the throtle steady at these rpm it stutter,but if i open the throtle,it accelarates with no prob... Second time,i took the carbs out for a more comprehensive clean this time. Nothing change.... I saw something weird to me... At the jets near down to the needle jet,i couldnt see through...  ,the same thing with the four of them. Now even i spray carb cleaner and compressed air. Is this normal??? I thing these are the "slow jets".Are these little flat screws(just to make my self clear...i think..) Thanks guys... 
14
« on: 17 August 2012, 08:57:35 pm »
Hello there focers! Just a quick question! Can somebody tell me how many turns out to unscrew the pilot air screw? 2 or 2,5??? my bike is an fzs 600 2001,with k&n air filter and danmoto carbon exhaust. Thanks guys!
15
« on: 22 October 2011, 08:19:19 am »
Hi focs. Trying to balance my carbs with Carbtune.But i think i have a problem. The bars have big amount of damping . I recently change the inlet rubbers(old had cracks),but the dumping still remain. The cartune setup is corrent(carbtune----90cm tube----restricters----10cm tube---- engine). What cause this problem.air leaks???where?? Hope for help... 
16
« on: 15 October 2011, 06:30:17 am »
Greetings from Greece Focers!!! I am willing to buy a clutch kit for my bike(fzs 600,2001 model). I am looking for a full kit (friction, steel plates and springs) not certainly all together as a kit,but at least from the same shop. First of all,what brand to prefer(better,most common)? EBC or FERODO??? i am more interested to ferodo...dont know why.. Plus, i find difficult to find steel plates no matter what brand is... I am always talking for an internet buy. Can you suggest me some e-shops or other links?? I will appreciate your help! Always good to be back forum!!! Thanks guys!
Pages: [1]
|
Show Posts
