This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Messages - WayneUK
76
« on: 28 January 2020, 11:07:52 am »
Some sun and nice weather please. 
77
« on: 26 January 2020, 01:10:21 pm »
I think the bolt head is 17mm and the washer is 14mm?
78
« on: 05 December 2019, 12:20:11 pm »
?
79
« on: 01 November 2019, 06:03:33 pm »
Hi,
Anyone got any black original bar ends for sale for the Fazer 1000 2003?
80
« on: 05 October 2019, 05:49:32 pm »
I'll take these, will you post?
81
« on: 24 September 2019, 11:01:30 am »
Mine has had the clear ones put on which I think look pretty good on the silver bike.
82
« on: 24 September 2019, 10:57:21 am »
Hi George,
Yes I'm interested in these if they are the kind I'm looking for,Could you post a pic of them by any chance please?
I've PM'd you.
Wayne
83
« on: 21 September 2019, 12:28:37 pm »
I have a full set of original crash bars that bolt directly onto the frame, they were on the bike when I bought it. I took them off and now just take up room in my garage. There are no bolts as I had to retain them, I'm guessing the bike's OEM bolts are long enough to mount the bars.
The front part of the guard clamps onto the down tube on either side of the frame, these are missing bolts as I needed them for something else, replacements should be easy to source.
If you're interested £50 plus postage.
Cheers
are these still available?
84
« on: 25 August 2019, 09:32:39 am »
Thank you
85
« on: 24 August 2019, 04:04:23 pm »
Mix however much is required for the bike
86
« on: 23 August 2019, 04:55:22 am »
ok thanks, do I mix the whole bottle with 1.5 litres of water?
87
« on: 22 August 2019, 02:40:08 pm »
fazer 1000 2003?
88
« on: 21 August 2019, 02:46:27 pm »
?
89
« on: 20 August 2019, 03:52:18 pm »
hi would this be ok to use in my bike?
90
« on: 31 July 2019, 11:33:13 am »
i had same problem with my 2003 with a beowulf fitted,
the guys at the dealers workshop said it doesnt need it with having that can on and said they can put a eliminator to stop the tach error,but didnt make any difference, but when the main mechanic came back from being off ill, he rang me and said it needs the exup sorting its not right without it,he had it for a week, he put new cables and valve in, as he said the one in was completely siezed, and now its been done what a difference it makes,I noticed the difference in sound soon as he started it up and now runs much smoother at low and high speed.
91
« on: 31 July 2019, 11:23:39 am »
ok thanks,
would any other bike models fit like a fazer 600 one fit ? or something else,
seems to be very limited on ones for the 1000
92
« on: 30 July 2019, 12:22:16 pm »
Hi,
Does anyone know of any engine guards/bars that are compatible with a 2003 FZS 1000?
93
« on: 29 July 2019, 03:08:26 pm »
Hi,
Looking for some Engine Bars to fit FZS 1000 Fazer 2003
94
« on: 26 July 2019, 02:19:29 pm »
Hi Everyone
This is my bike
95
« on: 26 July 2019, 12:07:39 pm »
Well. got bike back today after them sorting exup out , new cables and valve, now seems real smooth 
96
« on: 21 July 2019, 11:16:43 am »
thanks for the advise I'm taking it back in today
97
« on: 19 July 2019, 10:20:17 am »
Hi all, I've just recently bought a fazer 1000 2003, and it shows the EX UP fault , i took it back to the dealers and they have fitted a eliminator,but its still showing the fault?the valve has seized open but not connected by the servo, the fault doesn't seem to happen if im going over 50 mph, just seems to be below that? but some times seems to be ok on that, and always shows when the ignition is switched on,
it also has a beowolf exhaust
any advise on why it might still show up with a eliminator connected?
|
Show Posts
