This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Messages - gerkin
26
« on: 28 November 2018, 09:30:48 pm »
Is the quality of these good looking to replace switch on my 99 model
27
« on: 18 January 2017, 06:36:32 pm »
Collection preferred for big parts will post smaller parts
Essex 5mins m25 a127 junction
Good fuel tank
Fairing with minor marks
Will post pics of any parts required
28
« on: 22 December 2016, 05:57:26 pm »
29
« on: 10 April 2016, 06:06:17 pm »
30
« on: 10 April 2016, 06:01:00 pm »
Think this may be chain noise ,hardly any wear when tested at the rear sprocket only about 5mm daylight between sprocket and chain ,But loads of sideways movement and looks like there is 1mm of slight wear on the tyre edge wear chain may have been rubbing ,never had anything like this in 30 years of riding ,will fit new c&s and check back !
Cheers for all your replies
31
« on: 10 April 2016, 05:50:35 pm »
Bt023s
32
« on: 08 April 2016, 03:41:14 pm »
Put some off cuts of rubber between exhaust and centre stand cable tied tight noise still there
Dam n blast
33
« on: 08 April 2016, 03:18:54 pm »
Road tested today noise still there
Centre stand bung missing will fit gaffer tape something on and see if that cures it
Cheers gaz
34
« on: 07 April 2016, 07:25:54 pm »
Engine change Xmas 2015 checked all bolts the front mountings for the dhm mushrooms were slightly loose now tightened
Enough to cause the vibes?
,here's hoping !
,pissing down here will test on my commute in the morning
Cheers
35
« on: 07 April 2016, 06:40:34 pm »
I have a noise similar to bodywork vibrating and slight vibes but only below 5k revs
Don't make the noise when on centre stand in neutral or in gear
Suspected loose sprocket but which is tight output bearing seems fine
Removed clutch checked all OK
Brake pads appear OK is not loose and vibrating
No mudguards rubbing
Could it be water pump ? Really starting to p me off
Help!!!
Cheers gaz
36
« on: 03 August 2015, 06:26:07 pm »
ive had this ,its ok if oil level is at its highest in the site glass but comes on if near the lower mark
37
« on: 21 July 2015, 05:39:47 pm »
Cheers
38
« on: 20 July 2015, 09:33:07 pm »
My silencer has 600 and has started blowing where link pipe meets silencer can .is this common ?
Can I fit any silencer to my 2001 model.
39
« on: 25 June 2015, 08:14:13 pm »
Any one tried one of these are they any good?
40
« on: 17 March 2015, 07:18:18 pm »
+ 1 for the motad 140 quid inc delivery in 2010 ,so there getting cheaper!!??
41
« on: 13 March 2015, 05:00:11 pm »
bt23s need replacing what are the current recomendations ,
always found these ok but there are newer tyres about since i fitted these 4 years 12k ago
i need a good all rounder with good milage ,
cheers
42
« on: 26 January 2015, 06:51:07 pm »
I could be proved wrong here but people who have had cracked rubbers - incl me although they are cracked the crack is not all the way through with no performance issues.
A repair is black silicone and or self amalgamating tape
I know mine are covered in cracks on the outside but when I took carbs off about 5 years ago to clean heater tube out none of the cracks were the whole way through so just left them.
same with mine ,they are vey thick
43
« on: 26 January 2015, 06:46:46 pm »
44
« on: 22 January 2015, 07:22:13 pm »
love it
coyi
45
« on: 20 January 2015, 06:38:05 pm »
mine arrived today,great fast service ,well packed ,will use again
46
« on: 18 January 2015, 10:47:11 am »
47
« on: 17 January 2015, 06:26:25 pm »
where do you connect to the loom ?
fitting some to a mates 1000 fazer next week
cheers gaz
49
« on: 17 January 2015, 06:08:36 pm »
the last week this is becoming a right pain in the arse
,having trouble getting the key in and out ,worse when the sterring lock is on
so tight feels like the key is going to shear ,whats the best way to lube or clean
switch works perfect
cheers gaz
50
« on: 15 January 2015, 06:35:45 pm »
|
Show Posts
