Date: 28-04-24  Time: 13:49 pm

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Banger

Pages: [1]
1

Under seat code - 1C2A-050
Same OEM key for all locks on the bike.


Wires running back from the 2 red Loom connectors in the main connection bundle under the tank/coil -


Plug 1 - Red & Brown with blue stripe
Plug 2 - Black, Brown with a red stripe & Blue with a yellow stripe.


Cheers

2
one has 4 wires, another has 5 wires and the third one has 7 wires.


Hiya

Typically enough . . mine has 6 wires.

Red, Black, Brown, Brown with Red stripe, Blue with yellow stripe & Blue with black stripe.

Cannot see any evidence in the Loom or from the Barrel that there was ever a 7th wire ? 



3
Let me know if the all the ignition wires were bunched together when you got it back and if the pump works and I will PM you how to work around it.


All Ignition wires were twisted together, apart from Red, Black and Brown which were loose / separate when I got it back.
Must have been connected at some point tho.


Cannot hear any Relays kicking when . :(

New Ignition cut out Relay is £60, so not the end of the world. Be nice to be sure before I buy it though.
Unless anyone has a spare they would like to sell ?

4
Side stand up or down doesn't make any difference.

Know what you're saying Hugh/Pat. The damage isn't too heavy. If I can get it started I'll repair it.
Was really expecting to have heard it running before the Insurance Assessor comes out.   >:


I can't see what else it could be at this point other than the relay.


I've had the clocks off just now and checked all the connections there too and found nothing suspicious.
*Sigh.*

5
Just double checked the Clutch switch. No change with it in/ out / bridged.

Kill switch is Ok.

Left thinking either my Neutral switch is knackered - coincidentally, or they've fried the main relay when fiddling about with chopped wires . . ?



6
The starter button won't work cos your neutral light isn't working. Try pressing the start button with the clutch pulled in. If it starts then there is still a problem with the wires from the neutral switch as the bike thinks it's in gear.


Thanks for the reply.


I've just been down for another fiddle.


12V reading from the Neutral switch connection when ignition is on.
Starter will turn it over when lived direct from the Battery but it didn't fire.


I've jerry rigged a new clutch lever mount but the clutch isn't disengaging when the lever is pulled, clevis arm is moving but something is obviously not right there.


I was going to try and bump it but can't until I've resolved the clutch issue. Grgrr


7
Alarm wiring hacked out?
Fuses missing?


No Alarm fitted.
Main 20A fuse was blown but I've replaced this. All other fuses are OK. . . .

8
So, after a week of abject misery after my Fave bike - 05 Gen1 Fazer 100 - was stolen from my sisters drive by the local little scrotes, I have managed to retrieve it from the little darlings and get it back to the safety of my garage.

Insurance Assessor is due out next week so I thought I'd get a look over done first to see if it was worth buying it back to repair.

Good news is that all the big important things appear fine, wheels, forks, frame etc.

Having re-connected the chopped loom at the ignition I now have all lights, horn & oil light on dash but no Neutral light and the starter button is dead as a dodo. Nothing, not even a click.

Need to get it started asap to be sure the engine is sound so any help or advice on what to check now is welcome.

Possible causes ?

Ignition cut out relay behind L/H panel. Can this be tested ?
Side stand switch - checked & seems ok

Starter solenoid ?
Clutch switch ?  Clutch cable and lever are disconnected but switch bypassed.
Neutral switch failed ?


Any Advice please on where to go next ?

Pages: [1]