Date: 28-03-24  Time: 08:58 am

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - kralik

Pages: [1]
1
For Sale & Wanted / FS: 320mm Front brake discs + adapters set
« on: 17 June 2021, 09:23:35 am »
Hello,
I have got for sale this set of 320mm front brake discs to fit FZS1000 01-05 and R1 98-02 (probably early R6 as well) front wheel.
The set includes caliper adapters which enable calipers to fit with 320mm discs.The adapters are brand new bought this year and are made by Italian company named ALTH.The Brembo front brake discs are in good condition, rivets however are bit loosen and I would recommend to change them.Thickness of the discs are about 4,6mm both.

I wanted to use them on my bike however decided to keep my standard discs which I bought last year, so they are brand new.
I am located in Slovakia in EU. The price is 200€ plus shipping.

2
Fazer 1000/FZ1 corner / Fitting Ivan`s jet kit
« on: 06 December 2020, 10:06:07 am »
Hi all, me again.
I am just cleaning my carbs and getting everything ready to fit Ivans full monty kit.
The only information I cannot find is, how to set up Pilot screw. Unfortunately, I did not check how many turnst it was screwed from the fully in. Haynes manual does not say anything too.
Many thanks in advance.Kralik

3
Fazer 1000/FZ1 corner / Front brake caliper adapters for 320mm discs
« on: 01 December 2020, 08:45:10 am »
hi all,
 have seen one video on yt of a fzs 1000 with 320mm discs and adapters for use with standard calipers and forks.Does anyone know whether it is possible to find and buy them?
And did anyone this mod here?
tia

4
Fazer 1000/FZ1 corner / Does 4XV R1 rear wheel fit to gen1 FZS1000?
« on: 30 October 2020, 12:00:02 pm »
Hi all,dont you know whether the early R1 4xv rear wheel fits to gen1 FZS1000? I just like the look of the wider rear wheel.
Yeah, I tried 190 tyre in the original FZS rear wheel already, but the tyre was too bended in the tighter FZS rear wheel. Ok it was Pireli Supercorsa, which are pretty wide anyway.TIA

5
Fazer 1000/FZ1 corner / R1 fork conversion - what springs should be used
« on: 02 October 2020, 08:27:30 am »
Hello,after another advice.
I am going to do for conversion to 4xv R1 forks on my gen1 Thou, but I read that the standard springs in 4xv forks are soft and use to be changed to harder from Hyperpro etc.Would be anyone able to advice, what hardnes should I use, please?I am 90 kgs without leather, helmet and boots.
many thanks in advanceMarek

6
Introduction / I am new here
« on: 30 September 2020, 08:44:44 am »
Hi everybody here!
I am pretty new here, I used to read some topics earlier.I have got FZS1000 first gen, but I am not new to this as first time I bought the FZS was back in 2013.
It is really good and reliable bike, mainly from the engine point of view, however I dont know why I did not find this forum much sooner.I used to do trackdays with Fazer in the past, short & long circuits too.
Now, I am about to make few modifications to the bike, R1 front end, Ivans kit, maybe full exhaust system, or at least akra or arrow slip on.Basically, i have titanium Akra slip on at home, it has 60mm inlet, but I cannot find genuine Akra link pipe for it. It seems to be discontinued.
In addition, I would like to buy FZ1 gen2 too, if I will sell my second current bike.

7
For Sale & Wanted / WANTED: Akrapovic muffler or link pipe for S-Y10SO3-
« on: 30 September 2020, 06:20:47 am »
Hello,
I know these are like hen`s teeth but I try.
Does anyone happen to have Akrapovic muffler with link pipe S-Y10SO3- for FZS1000 gen1 for sale, please?
Or at least, if anyone would have link pipe L-Y10SO3 for sale, it would great.
many thanks in advanceMarek

Pages: [1]