Date: 20-09-21  Time: 18:44 pm

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Macca4786

Pages: [1] 2
1
General / Re: Renthal Bars
« on: 20 April 2015, 10:51:59 pm »
I have bought these as I sent my bike down the street on its side. I was quite happy with my old ones until they where pointing the wrong direction

2
General / Re: Renthal Bars
« on: 20 April 2015, 05:02:53 pm »
Brilliant thanks again Steve something new learned again. Not a great idea to come off your bike but it certainly gives you some great knowledge putting it back togther !! Lol

3
General / Re: Renthal Bars
« on: 20 April 2015, 04:53:19 pm »
Ok Steve

Aslong as that's the normal thing to do I am happy with that. I presume the tape is just something for the bits to grip onto therefore can be any tape ?

Danny

4
General / Re: Renthal Bars
« on: 20 April 2015, 04:47:59 pm »
Ignore the end bar comment just after advice about lug holes to locate my switched and throttle etc

5
General / Renthal Bars
« on: 20 April 2015, 04:36:02 pm »
Evening all

Possibly another daft question if you know what your talking about but I don't so here goes.....

Just ordered and received some Renthals
And they have turned up but don't have the lug holes for my bits and bobs to sit in ?

Is this normal ?

Also I don't think I can install bar ends on these bars ?
Thanks

Danny

6
Messages for Users / Deefer66
« on: 14 April 2015, 10:49:22 pm »
Need to speak to Deefer about some fairing work I may want doing.

Could anyone put us in touch

Danny

7
General / Re: Front fairing 1998 Fazer
« on: 14 April 2015, 08:06:07 pm »
How do you private message Pete ? Yeah have all the bits

8
General / Front fairing 1998 Fazer
« on: 14 April 2015, 07:46:56 pm »
Evening again

So it's true fairings for my 1998 Fazer are like rocking horse s"£!.

Just after some advice really. I have attached pictures below and want to know would you experienced bikers say this fairing could be repaired ?

If so what would you expect to pay ?

Thanks in advance

9
General / Re: First Crash
« on: 12 April 2015, 08:12:06 pm »
Cheers all. Only used this forum twice and it's bloody brilliant ! now to find a fairing !!

10
General / Re: First Crash
« on: 12 April 2015, 07:43:45 pm »
That's the colour then yeah ?

11
General / Re: First Crash
« on: 12 April 2015, 06:11:43 pm »
Yeah under the seat it says 5DM4 070 so it's the 1999 red on an 1998 bike !
Can't imagine I shall be that lucky to get the right colour so will now look at spray painters in my area

12
General / Re: First Crash
« on: 12 April 2015, 05:45:48 pm »
That's sounds about right bud ! Just going under the seat now to have a look

13
For Sale & Wanted / Wanted 1998 Fazer Fromnt fairing
« on: 12 April 2015, 05:31:25 pm »
Evening guys

After my first dismount of my biking career I am now looking for a front fairing if anyone has one to sell?

Cheers Danny

14
General / First Crash
« on: 12 April 2015, 04:28:35 pm »
Evening all

Had my first spill over the bank hols. Broken finger was all I got fortunately.
However the pride and joy is not looking great. Exhaust snapped off and my front fairing is slightly U/S.
Anyone got a front fairing kicking about or know of any breakers with them ?
Also did they do the 1998 Fazer in 2 reds. I don't know if it's just be but my bike looks a darker red than some I have seen??

Thanks in advance for any help


15
General / Fazer 98 End Can
« on: 14 January 2015, 11:39:27 pm »
Evening All

Spent another evening browsing the Internet looking for a new end can for my 98 Fazer. Any one got any good sites to have a look on ?
And any advice or recommendationsof what to put on ?
Had a look at eBay but full of Chinese parts which am not to keen on !
Anyone point me in right direction



Thanks

Danny

16
General / End Can for Fazer 98
« on: 10 October 2014, 01:36:11 pm »
Afternoon Everyone

Looking for a bit of advice ! Standard end can has had it so looking to replace it ! Any thoughts on a good end can ? Is an older fazer 1998 so not looking to break the bank ?

Cheers

Macca

17
I bought my fazer last summer and was new to the biking world ! Got advised to change chain and sprockets so I new the mileage on them ......
Thank god I till advice !

18
General / Chain and sprockets
« on: 19 August 2014, 10:21:00 pm »
Evening all

So time has come for me to replace my chain and sprockets any suggestions on what make to go for ? All new to the biking world so appreciate any advice ! What should I be looking to pay ?

Thanks

Danny

19
FZS600 Fazer / Downpipes advice
« on: 01 May 2014, 08:49:26 pm »
Evening all


So as a bank holiday project i have removed the downpipes off my Fazer as they were looking a bit shabby. I am taking them to work tomorrow and hoping to get the hole welded which is quite big right near the top where they connect to the engine block. (not even sure if it can be welded so fingers crossed). :(


Once they are welded i obviously need to paint them, anyone any ideas whats best to do regards painting?? Don't want it to be flaking off after 3 months but also don't want to spend 100's on getting them professionally finished. Any good recommendations on paint ??

Or do people just recommend on stop wasting my time and replace them ??

Thanks


Danny

20
FZS600 Fazer / Re: Speedo Sensor Needed
« on: 17 April 2014, 10:39:13 pm »
Apologies didn't realise there where two pages to the forum. Question now answered, would be helpful though if anyone who has bought the washer could post a website I could purchase one. Thanks again everyone

Danny

21
FZS600 Fazer / Re: Speedo Sensor Needed
« on: 17 April 2014, 10:34:15 pm »
So I have this problem also, had my front tyre changed today and now speedo is not working at all. Do. Need to be looking for just the tab washer (drive dog) or is it a complete unit inc the cable and everything?

New to bikes so any help is appreciated !

Danny

22
General / Speed sensor
« on: 17 April 2014, 10:06:48 pm »
Evening guys,

Today I had my tyres replaced on my 1998 Fazer. Unfortunately the speed sensor washer tabs snapped whilst swapping the front tyre. Does anyone know where I could get one ? And also do I have to by the complete unit including the cable or can I just replace the tab washer ?

Hopefully I have explained this a ok. Still in the learning stages of bikes !

Danny

23
Introduction / Re: Newbee
« on: 26 January 2014, 07:17:53 pm »
Here's some pics !! Love it ! Glad I listened to the advice whilst buying first bike !

24
FZS600 Fazer / Re: Please Help !!
« on: 26 January 2014, 06:55:02 pm »
Well after an afternoon/evening in the garage i am finally sorted. I found the correct place for the idle adjuster thanks to Red98 for the pictures.
Wasn't the easiest to get back in but a bit of persistence paid off. Running like a dream again at 1100 RPM.


Thanks to everyone who posted and helped me out took all your points on board for the future.


Just wait for some nice weather now.  :D


Thanks again


Danny

25
Introduction / Newbee
« on: 26 January 2014, 06:48:51 pm »
Hello all,


New to biking got myself a Fazer 600 in September last year so looking forward to my first full summer riding. Brilliant forum that has already helped my with some issues !!


I am in the Lincolnshire area near Sleaford.


Danny

Pages: [1] 2