Date: 20-10-21  Time: 14:06 pm

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - Macca4786

Pages: [1]
1
General / Renthal Bars
« on: 20 April 2015, 04:36:02 pm »
Evening all

Possibly another daft question if you know what your talking about but I don't so here goes.....

Just ordered and received some Renthals
And they have turned up but don't have the lug holes for my bits and bobs to sit in ?

Is this normal ?

Also I don't think I can install bar ends on these bars ?
Thanks

Danny

2
Messages for Users / Deefer66
« on: 14 April 2015, 10:49:22 pm »
Need to speak to Deefer about some fairing work I may want doing.

Could anyone put us in touch

Danny

3
General / Front fairing 1998 Fazer
« on: 14 April 2015, 07:46:56 pm »
Evening again

So it's true fairings for my 1998 Fazer are like rocking horse s"£!.

Just after some advice really. I have attached pictures below and want to know would you experienced bikers say this fairing could be repaired ?

If so what would you expect to pay ?

Thanks in advance

4
For Sale & Wanted / Wanted 1998 Fazer Fromnt fairing
« on: 12 April 2015, 05:31:25 pm »
Evening guys

After my first dismount of my biking career I am now looking for a front fairing if anyone has one to sell?

Cheers Danny

5
General / First Crash
« on: 12 April 2015, 04:28:35 pm »
Evening all

Had my first spill over the bank hols. Broken finger was all I got fortunately.
However the pride and joy is not looking great. Exhaust snapped off and my front fairing is slightly U/S.
Anyone got a front fairing kicking about or know of any breakers with them ?
Also did they do the 1998 Fazer in 2 reds. I don't know if it's just be but my bike looks a darker red than some I have seen??

Thanks in advance for any help


6
General / Fazer 98 End Can
« on: 14 January 2015, 11:39:27 pm »
Evening All

Spent another evening browsing the Internet looking for a new end can for my 98 Fazer. Any one got any good sites to have a look on ?
And any advice or recommendationsof what to put on ?
Had a look at eBay but full of Chinese parts which am not to keen on !
Anyone point me in right direction



Thanks

Danny

7
General / End Can for Fazer 98
« on: 10 October 2014, 01:36:11 pm »
Afternoon Everyone

Looking for a bit of advice ! Standard end can has had it so looking to replace it ! Any thoughts on a good end can ? Is an older fazer 1998 so not looking to break the bank ?

Cheers

Macca

8
General / Chain and sprockets
« on: 19 August 2014, 10:21:00 pm »
Evening all

So time has come for me to replace my chain and sprockets any suggestions on what make to go for ? All new to the biking world so appreciate any advice ! What should I be looking to pay ?

Thanks

Danny

9
FZS600 Fazer / Downpipes advice
« on: 01 May 2014, 08:49:26 pm »
Evening all


So as a bank holiday project i have removed the downpipes off my Fazer as they were looking a bit shabby. I am taking them to work tomorrow and hoping to get the hole welded which is quite big right near the top where they connect to the engine block. (not even sure if it can be welded so fingers crossed). :(


Once they are welded i obviously need to paint them, anyone any ideas whats best to do regards painting?? Don't want it to be flaking off after 3 months but also don't want to spend 100's on getting them professionally finished. Any good recommendations on paint ??

Or do people just recommend on stop wasting my time and replace them ??

Thanks


Danny

10
General / Speed sensor
« on: 17 April 2014, 10:06:48 pm »
Evening guys,

Today I had my tyres replaced on my 1998 Fazer. Unfortunately the speed sensor washer tabs snapped whilst swapping the front tyre. Does anyone know where I could get one ? And also do I have to by the complete unit including the cable or can I just replace the tab washer ?

Hopefully I have explained this a ok. Still in the learning stages of bikes !

Danny

11
Introduction / Newbee
« on: 26 January 2014, 06:48:51 pm »
Hello all,


New to biking got myself a Fazer 600 in September last year so looking forward to my first full summer riding. Brilliant forum that has already helped my with some issues !!


I am in the Lincolnshire area near Sleaford.


Danny

12
FZS600 Fazer / Please Help !!
« on: 26 January 2014, 07:59:29 am »
Morning all.

As you will be able to guess from the terms I use in my question I am new to riding and I have a problem!
Yesterday was a fairly nice day so after 8 weeks in the garage out came my pride and joy my 1997 fazer . I struggled to start it at first but  I finally got it going, any suggestions about why it was struggling please feel free. The ignition was working just wouldn't fire for about 20 mins  even on full choke etc.

Anyway  here's the issue. For some stupid reason I messed with the circular knob on the left hand side of the bike which adjusts the RPM.  I now cannot find where it was set to so I have zero revs on my bike unless the choke is on ! Stupid I know but lack of experience I just tried everything when it wouldn't start . I keep turning the RPM adjuster but it doesn't seem to do anything. Is it possible I have broken it ?

Any suggestions are welcome as am gutted at The minute first bike an all that and am hoping it not an expensive fix right before the new season !!!

Thanks for you time and any replies in advance

Danny


Pages: [1]