Max 1mm of play at the end of the swingarm. Basically if you can feel any knocking at all and the shaft is correctly torqued, your bearings are shot. Make sure you don't confuse swingarm play with wheel bearing play.
I've ordered some new bearings, I'll have a look at the pivot shaft when I take it apart when the bearings come.
Will I be ok to take the swing arm off with the bike on the centre stand?
Quote from: WayneUK on 30 July 2020, 11:25:02 amI've ordered some new bearings, I'll have a look at the pivot shaft when I take it apart when the bearings come.Don't forget to check the thrust/cover seals, it's bee a while since I taken them off but I'm fairly certain there's a seal built in, if it's buggered they'll need replacing and you don't want to have to do the job again QuoteWill I be ok to take the swing arm off with the bike on the centre stand?Yes, just make sure you take off any top boxes/panniers etc and bungee/cable tie the front level also be aware with lateral pushing/pulling. The swingarm should come out fairly easily, if you're forcing anything it's wrong stop and recheck
Will I be ok to follow these steps or will I need to do or should do anything differently as this looks like a 600?https://foc-u.co.uk/index.php?topic=72.0
Quote from: WayneUK on 01 August 2020, 08:40:33 amWill I be ok to follow these steps or will I need to do or should do anything differently as this looks like a 600?https://foc-u.co.uk/index.php?topic=72.0Not a bad guide I would add clean the whole back end first, I mean proper de-grease and jet wash the under tray, get off all the old chain lub and dirt.
Ok so having a look around while waiting for the bearings to come, in case I'd need the pivot shaft, in the guide he calling the pivot shaft wrong?He has the bush and bearing and the pivot shaft is the one that bolts the swing arm on with the bolt on?
Quote from: WayneUK on 01 August 2020, 11:37:47 amOk so having a look around while waiting for the bearings to come, in case I'd need the pivot shaft, in the guide he calling the pivot shaft wrong?He has the bush and bearing and the pivot shaft is the one that bolts the swing arm on with the bolt on?The bush (pivot shaft/s) new/old in the picture are at the bottom, the bolt or officially named pivot shaft is above these, with a washer and nut on, it goes through the bush (pivot shaft) which is hollow. Look here https://www.fowlersparts.co.uk/parts/4175435/fzs1000-fazer-5lv8-2002-080-a/rear-arm bush is No 2, pivot shaft No 5.
T looks like the arm relay bearings ?
Quote from: WayneUK on 03 August 2020, 05:02:58 pmT looks like the arm relay bearings ? ??
Mate if the end of the swingarm is moving side to side it's not the shock relay bearing. Now hold a minute, when you say your swingarm is moving are you meaning up and down or side to side?
Gnasher will correct me where Im wrong or am bike agnostic - But that could be the swing arm bearing, one of the bearings in the suspension linkages, or possibly even a rear wheel bearing. When you say you have up/down play how are you seeing/feeling this..? When an MOT tester checks all of the above for free-play, they stand behind the bike and put both hands on the rim of the rear wheel and gently but firmly pull upwards a few times. And as others have asked, how much free play are you seeing/feeling? If the movement is almost imperceptible, then that's most likely an MOT advisory. But back to narrowing down where the play is - If you haven't done so already the first thing to so is remove the rear wheel, then with the sprocket carrier and axel in-place put your knee/chest on the top of the wheel and again pully gently but firmly on the axel and check for free-play - there should be none that you can feel, if there is you should replace all the wheel bearing as you can replace just one (good pattern bearings are cheap enough now)When the rear wheel out same as before grab the ends of the swing-arm and check for free-play. If you feel any its either a linkage bearing or swing-arm bearing.Remove the suspension linkage and using the bolts that go through the roller bearing check for lateral movement, as in up/down or diagonally. If there is any movement the bearings and/or the bolts will need to be replaced. Note - I think the bearings in the linkage may need to be pressed out and new ones pressed in, but don't quote me on this.If your wheel bearings and your suspension linkage bearings are fine, then that only leave the swing arm bearings. The only test I can think that 'might' show wear is to hold both arms and try a gently but firm twisting motion. If there is any free-play then replace the bearing and check the swing-arm excel for wear.
Sure, but I think we will only able to see any play if its 'really' bad. If its just normal wear that requires replacement of any of the bearings you will mostly likely only be able to feel this and not see it.