Date: 28-04-24  Time: 17:51 pm

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - gnm

Pages: [1]
1
Fazer 1000/FZ1 corner / Fz1 centre stand
« on: 18 March 2018, 11:10:01 pm »
Hi all, I’ve fitted an aftermarket link pipe and it doesn’t have the bracket for the centre stand to stop against. It stops in the same position anyway but will it do any harm without the stop

2
Fazer8 / FZ8 / Fz1 centre stand
« on: 18 March 2018, 10:54:34 pm »
Hi all, fitted a new link pipe to gen2 and it doesn’t have the bracket on it for the stand rubber to stop against. Will this matter as it stops at the right place anyway or will I need to make up a bracket for it?

3
For Sale & Wanted / Gen 1 link pipe
« on: 18 March 2018, 10:44:27 pm »
Link pipe for after market end can £30 posted

4
For Sale & Wanted / Gen 1 parts
« on: 27 January 2018, 08:23:35 pm »
Hi all, recently changed to a gen2 so have some bits for sale. Fairing lowers with brackets/bolts no cracks or repairs but a few scratches and marks on lacquer £80 + post. Crash bungs £20 +post. New clutch cable and used exup cables £10 the pair +post and 2 workshop manuals one Haynes and one copy of Yamaha manual £12 each +post the Yamaha ones a bit heavy so post won’t be cheap for it. iPhone won’t let me upload photos for some reason but they are on gumtree you could see pics there or I could WhatsApp them to anyone interested.

5
Fazer 1000/FZ1 corner / Will it fit?
« on: 13 January 2018, 04:25:38 pm »
Hi all, I’m trading in my gen one for a 2011 gen 2. Question is will the stubby end can from gen one fit the gen 2 if I got a new link pipe or would I be as well buying a new system?

6
Fazer 1000/FZ1 corner / Overheated?
« on: 24 December 2017, 08:36:10 pm »
Hi all, started the Fazer up last night after about 8 weeks in the shed and left it running for about 20 minutes then it cuts out. When I went to check it there was steam and water coming out from around the rubber overflow pipes behind the exhaust link pipe. I left it to cool down then tried to resart it but only getting a loud clicking from around the positive side of the battery any ideas?

7
Fazer 1000/FZ1 corner / Gen 1 paint code
« on: 15 May 2016, 05:58:46 pm »
Anyone know how to find paint code? There is a sticker on the frame near the front but does not mention colour code. Another sticker under the seat but nothing on it either. It's a 2004 sort of mid blue?

8
Fazer 1000/FZ1 corner / rear wheel bearings
« on: 01 April 2016, 09:49:11 pm »
hi all,   just noticed a bit of play on rear wheel bearings, has anyone used the all balls kit from wemoto? also any problems fitting or any special tools needed to fit them?

9
Fazer 1000/FZ1 corner / genuine fairing?
« on: 21 September 2015, 09:59:01 pm »
saw this in cannes when passing through on hols. does anyone know if its a yamaha part or some other supplier? any idea if they are still available ?

10
Fazer 1000/FZ1 corner / gen 1 rough running at 6000 rpm
« on: 15 August 2015, 09:19:55 am »
any ideas what its likely to be?  runs fine up to approx 6000 then just starts to misfire, let throttle  off slightly and it goes fine. sometimes runs fine but theres no telling when its going to do it. replaced exup cables, cleaned and lubed valve about 2000 miles ago after 7000 message on tacho.

11
Fazer 1000/FZ1 corner / wemoto cables
« on: 25 April 2015, 12:02:14 pm »
exup cables getting frayed so looking to replace them. seen some slinky glide cables from wemoto at £55ish just wondering if anyone has used them or heard of any problems with them ?

12
Fazer 1000/FZ1 corner / oxford heated grips controller
« on: 01 March 2015, 06:47:08 pm »
can anyone advise if an oxford v8 control box will replace a v5? as there does not seem to be any v5 boxes for sale.

13
For Sale & Wanted / wanted
« on: 06 January 2015, 06:23:36 pm »
looking for a sports rack for gen 1 fazer 1000 would prefer yamaha one.

Pages: [1]