Date: 01-05-24  Time: 05:23 am

Author Topic: no heating....  (Read 1550 times)

red98

  • GP Hero
  • ******
  • Posts: 6,567
    • Main bike:
      FZS 1000 Gen1
    • - FZS600,CB400/4,X7,CB250
    • View Profile
no heating....
« on: 15 December 2013, 10:26:47 am »
woke up this morning and no heating...hot water ok though...traced the fault to a blown "central heating control" in the airing cupboard....looks a bit burnt and iam surprised we did`nt hear it go.....its a drayton tempus seven about 18 years old,looking at b + q thares lots to choose from and a dont know which one i need.......any experts out there ?
One, is never going to be enough.....

pilninggas

  • Club Racer
  • ****
  • Posts: 330
    • Main bike:
      FZ1 Faired Gen2
    • View Profile
Re: no heating....
« Reply #1 on: 15 December 2013, 12:17:09 pm »
I used to fit these occasionally, but not anymore due to Part P.

Screwfix do sell a Drayton 7-day tempus:

http://www.screwfix.com/p/drayton-tempus-7-programmer/37586

Easy to fit, usually 6 or 4 wires depending on whether there is a thermostat.

Only do it if you are competent and can definitely isolate it before removing the cover.

locksmith

  • FOC-U Official Selfish Bastard
    A bit of a cheapskate
    imageJune 09
  • GP Hero
  • ******
  • Posts: 9,947
    • Main bike:
      Other
    • - MT-09 :)
    • View Profile
Re: no heating....
« Reply #2 on: 15 December 2013, 12:40:02 pm »
A year or so I bought a new programmer as I was getting interference on the TV and it was suggested this may be the cause.
It was a Honeywell one so I bought the same make but a current model for easy installation. Wrong - wiring was all different and I didn't want to foc up the new boiler so a local sparky charged me £40 to wire it in.

Cured the TV problem as well !!

red98

  • GP Hero
  • ******
  • Posts: 6,567
    • Main bike:
      FZS 1000 Gen1
    • - FZS600,CB400/4,X7,CB250
    • View Profile
Re: no heating....
« Reply #3 on: 15 December 2013, 12:47:27 pm »
just been to b&q and bought new programmer and thermostat...themo is the same and will fit original wall plate.....programmer is updated version which they say will work....going to check drayton website before i fit.....
One, is never going to be enough.....

esetest

  • GP Hero
  • ******
  • Posts: 1,148
    • Main bike:
      FZS 1000 Gen1
    • - MotoguzziV7racer
    • View Profile
Re: no heating....
« Reply #4 on: 15 December 2013, 02:19:40 pm »
If you are going to diy make a note of the connections before you start , just in case you have to call in a sparky .

red98

  • GP Hero
  • ******
  • Posts: 6,567
    • Main bike:
      FZS 1000 Gen1
    • - FZS600,CB400/4,X7,CB250
    • View Profile
Re: no heating....
« Reply #5 on: 15 December 2013, 02:47:39 pm »
all fitted and working.thanks for all replys....nice and toasty now.the old thermostst was stuck at full throttle so iam hoping my mpg has improved......will check this afternoon   ;)
One, is never going to be enough.....

ddtwelve

  • WSB Pack Hound
  • *****
  • Posts: 561
    • Main bike:
      Other
    • - triumph tiger 1050
    • View Profile
Re: no heating....
« Reply #6 on: 15 December 2013, 09:05:19 pm »
your missus been sticking therm on full ;)