skullcandy low rider headphones in crosser helmet is the best and easiest option (did this back in the 50cc 125cc days)

finally finished respraying it,
just need decide on stickers for side of bike either thinking something like stock fazer(red and white though) or yamaha speedblock graphics

http://www.fz6-forum.com/forum/fz6-mods/342-touring-screen-fz6.html

why not try an r6 akropovic megaphone exhaust?
http://www.akrapovic.com/typo3conf/ext/user_products/mod1/uploads/products/slip_on_megaphone_exhaust_system_for_the_yamaha_yzf_r6_2008_2009_/fedd36fa52553fe17cf4b5423b623fe0.jpg
never seen one on a fazer before (someone probably has one)

if the wheels have never been painted get some strong nail polish remover or thinners and rub on the area where you dont want the black paint anymore use some masking tape on the center and after a little rubbing it will go to the steel of the wheel just do this wash it dry it leave it a while then lacquer it to stop rust.

well i realized this after a lot of searching
if any one cares though the fazer swing arm pivot width is 240mm i think (measured yesterday)


a vfr 750 (mk2?) swingarm is around 135mm i think so if someone ever wanted try it, it is possible but i came to the point where i decided that it would be hard the align the sprocket etc so i gave up, oh well i think i will just buy an r6 swingarm with brace and grind it off and get someone capable to tig weld it on (with a little modification)


thanks for replys anyway

basically 2nd gear is focced

how are you guys getting to 55+ mpg im getting 35-42?

okay ill be interested if its not too bad where about is the wheel in the U.K lol ?

i used baby oil worked a treat thanks

im sure the thundercat uses a bigger wheel so unless on the furthest back setting on swingarm doubt it tbh


different swingarms

Electrical and Electronic engineers 
and looking at your board its more a case of writing the assembly code,
the speedo drive goes into a 3 wire connector im not too sure ec what each wire is.
RED-          (POSSIBLY 5V?)
WHITE-      (POSSIBLY GROUND)
BLACK-      (POSSIBLY NEUTRAL)
either way it should give a digital output (square wave) for each rotation it sends a voltage which would register as a one, all basic stuff really.


Alternatively get a fzr (cable drive speedo pickup) fit it to your fzs then just buy a cheap analogue gauge (£30 on ebay i think) then simply just make a circuit for the rev counter ....


infact i had an idea for a new dash setup here it is sorry for babbling on about it.....


FZR cable speedo drive pickup         http://i.ebayimg.com/t/90-Yamaha-FZR600-FZR-600-Speedo-drive-Cable-/00/s/MTIwMFgxNjAw/$(KGrHqNHJCUE9!M2DEVNBPT+!pWus!~~60_57.JPG

Universal speedometer clocks    http://www.bajadesigns.com/images/items/Large/370002.jpg

5 green leds   (represents 1k -5k)       http://www.earthshineelectronics.com/40-91-large/5mm-green-diffused-led-s-pack-of-10.jpg

4 yellow leds   [size=78%](represents 6k -10k)          [/size]https://www.egr.msu.edu/eceshop/Parts_Inventory/images/5mm%20yellow%20led.jpg[size=78%]

3 red leds        [/size][size=78%](represents 11k -13k)       [/size][/color]http://www.basicmicro.com/assets/images/b0058_red_led.jpg[size=78%]

some skills in DIYpatients wire    ://egscontrols.com/thhn_wire_1.jpgsoldering kit (possibly?)   http://www.toolstation.com/images/library/stock/webbig/57891.jpg5 blue leds            (fuel gauge)    http://www.sciencephoto.com/image/346754/large/T3560583-Blue_LED-SPL.jpghere goes...basically make a small op amp circuit to amplifier ---------------- THIS IS PART A wrap wire around the ht lead, possibly 4 coils and secure with tape -----------------this is part Buse part a as an input to part b------------this amplifies the signal into a usable range tap of resistor of different values (you will have to determine this) set the resistors so that when the output voltage from the amplifier turns on a led as you increase rpm therefor voltage or current something like that more leds will light up 

the same principle applys for the fuel gauge using the original fuel sensor as the voltage input


then as for the speedo just replace stock fzs drive with the fzr cable drive and then screw into the analogue cable speedo




not sure what links im allowed to post but oh well..








lots of errors above very sorry, i need sleep..



[/size]

from this



to this





to this,
needs a really good clean but this will do for now