76
Fazer 1000/FZ1 corner / Re: R6 shock Mod fazer 1000
« on: 31 July 2017, 07:30:25 am »
Go to first post or Google r6 rear shock all the info is out there
Or email me devilsyam@gmail.com
Or email me devilsyam@gmail.com
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to. 76
Fazer 1000/FZ1 corner / Re: R6 shock Mod fazer 1000« on: 31 July 2017, 07:30:25 am »
Go to first post or Google r6 rear shock all the info is out there
Or email me devilsyam@gmail.com 77
Fazer 1000/FZ1 corner / Re: R6 shock Mod fazer 1000« on: 17 July 2017, 06:10:58 pm »
replied and http://www.helpforheroes.org.uk/give-support/donate-now/
also i have a rare mint YELLOW one arriving next wens if you want the ohlins look with out the price email me devilsyam@gmail.com first come first served 78
Fazer 1000/FZ1 corner / Re: R6 shock Mod fazer 1000« on: 10 July 2017, 09:55:02 pm »
replied to pm
79
Fazer 1000/FZ1 corner / Re: Oil pump chain slack fzs 1000« on: 18 June 2017, 10:25:28 pm »
how many miles kilo
80
Fazer 1000/FZ1 corner / Re: R6 shock Mod fazer 1000« on: 17 June 2017, 09:39:22 pm »
ok devilsyam website is coming down for major revamp as out dated and was built with front page which no longer is supported so will be moved to new format -- this will take some time so i have created a info page on facebook with reasons for this mod and a page of feedbacks
https://www.facebook.com/Fazer-1000-mods-page-1878273662426513/ 82
Fazer 1000/FZ1 corner / Re: R6 shock Mod fazer 1000« on: 09 June 2017, 06:55:06 pm »
can you bell me as to much to write 07736008778 ill try to help
83
Fazer 1000/FZ1 corner / Re: R6 shock Mod fazer 1000« on: 09 June 2017, 05:22:10 pm »
defo wouldnt have preload on rear that high be like a brick did i supply this shock?
84
Fazer 1000/FZ1 corner / Re: High speed weave ktec springs and 10w oil« on: 08 June 2017, 07:58:07 pm »
see replies in r6 thread to same question and i also suggested tmations point
85
Fazer 1000/FZ1 corner / Re: R6 shock Mod fazer 1000« on: 08 June 2017, 07:56:56 pm »
as this has happened after fork fit id be inclined to check front setting look for for sticksion make sure both legs have same setting
go back to factory settings as yo need a base point to work from sticksion is when the fork are clamped either resting on the deck or if yokes tightened oddly the way to remove it is lift front end remove wheel undo clamps so legs are relaxed nip uo lower yoke first just enough to hold the leg now tighten top yoke bit at a time left then right till both are torqued now undo the lower yoke till bolts are loose this allows any tension out again clamp either side bit by bit till torqued assuming all bearings are good and your happy go try it also ive come across alot of fazers in my time were the front wheel is over tightened so check torque on this to let me know how you get on 86
Fazer 1000/FZ1 corner / Re: Fitting a manual cam chain tensioner« on: 27 May 2017, 09:40:03 pm »
remove old adjuster and offer up new screw thread in on new one till face to face ie the length of new onw matches old one then back out one turn fit and follow vid
87
Fazer 1000/FZ1 corner / Re: Fitting a manual cam chain tensioner« on: 26 May 2017, 11:04:57 pm »88
Fazer 1000/FZ1 corner / Re: R6 shock Mod fazer 1000« on: 26 May 2017, 07:25:19 am »
Great thxs for the feedback
89
Fazer 1000/FZ1 corner / Re: FZS 1000 Manual Cam chain tensioner« on: 21 May 2017, 09:06:35 pm »
It's worth it I've personally had to deal with three busted bikes because of this failure ignore at your peril
Search youtube devilsyam and there's a vid on setting them 90
Fazer 1000/FZ1 corner / Re: frame bung / cap« on: 15 May 2017, 09:48:51 pm »
yep i have another robbo
91
Fazer 1000/FZ1 corner / Re: frame bung / cap« on: 13 May 2017, 10:23:38 pm »
il;l need to look i know i have one ill get back to ya
92
Fazer 1000/FZ1 corner / Re: frame bung / cap« on: 13 May 2017, 06:35:06 pm »
yep email me your address to devilsyam@gmail.com and ill send you one
93
Fazer 1000/FZ1 corner / Re: R6 shock Mod fazer 1000« on: 12 May 2017, 10:22:39 pm »
Black sold red in stock as of Thursday
94
Fazer 1000/FZ1 corner / Re: R6 shock Mod fazer 1000« on: 08 May 2017, 07:06:24 pm »
black in stock friday
96
Fazer 1000/FZ1 corner / Re: Clock Rings« on: 15 April 2017, 11:56:50 am »
Yeah I used to do them stopped about seven years ago lack demand etc
98
Fazer 1000/FZ1 corner / Re: FZS1000 Head Bearings« on: 06 April 2017, 08:18:40 pm »
tip 18" 1/4 round bar bend one end 30 degrees grind back the inner face but leave a 1/16 flat this will whack out bottom and top set easy before refit feel the inner face till you find the groove i further opened this up with a dremel in case i needed to go back in
99
Fazer 1000/FZ1 corner / Re: R6 shock Mod fazer 1000« on: 02 April 2017, 06:59:20 pm »
well thats 3 times the time a stock will last lol ive had them go to 50k nick but they will eventually need overhauling
|