what did you do with your fazer today ?

[NorthWestern]

Taxed it...  Searched the net for a rear tyre, looking like it's going to be a pr3 this time round

[red98]

not today but thursday...went down to the haynes motor museum in sparkford,not as good as i had hoped but nice to know they have a "red room  "..from there north to cheddar gorge and then onto weston-super-mare for fish and chips,home via the A638 to bath passing blagdon lake.a nice scenic route with twisties and aviods bristol and motorways.onto the A4 at bath all the way home.more or less had the road to myself 

[Skippernick]

And you didn't stop to say hi


Mind you some of us was at work!

[pilgo]

And you didn't stop to say hi


Mind you some of us was at work!

as above,except ive had the week off and could of joined ya 

[red98]

Sorry foccers  .....next time iam out I'll post before leaving   

[woodwizzard]

Went for a quick spin this morning, still need to get the front suspension right, still chattering over bumps. The Fabbri DB is a little better and reduces the wind blast/buffeting from my shoulders, but the wind noise around my head is a little worse. Fitted the wiring for my heated gloves when I got back.

[pilninggas]

Rode up and down the Trollstigen - what a road, almost alpine.

[mickvp]

Checked my coolant levels after changing it and going a short ride yesterday, then went out a run across the dukes pass in aberfoyle and back.

[Andy FZS]

Mickvp , how was removing the ais and how was the holeshot kit. I'm thinking of doing mine later in the year and looking for a bit of advice on how best to do it.
Cheers Andy

[mickvp]

Hi Andy,

Doddle mate. Although the step by step guide on pats site is for the Ivan's removal kit, most of the steps are still the same so I followed that for the most part.

The hole shot kit is very well made, one thing to bear in mind though is that you will need blue high temp locative for the grub screws (loctite 242), and you also need some copper based high temp gasket sealant as well which you stick in the aluminium bungs before fitting to make sure you get a seal.

You will also need a few litres of coolant as well as removing the radiator is required for access.

Really simple, a bit fiddly to get the AIS out from the top once all the pipes and bolts are off, but it just takes a bit of wiggling to get it oriented right to come out.

It does give a good bit of extra space above the engine though, so it's worth doing if you want a wee bit more extra room in there, and a tiny weight saving as well.

 I've noticed the bike doesn't seem to pop and bang on a closed throttle as much since doing it, but I assume that's normal.

[Lez72]

Looked at them lovingly 

[Ten2Ten]

Put in new coolant after rad fuse blew and gushed out like a shaken bottle of coke,100000 miles on clock and was the first bit of bother from new.

[slimwilly]

Put in new coolant after rad fuse blew and gushed out like a shaken bottle of coke,100000 miles on clock and was the first bit of bother from new.

a bit of a troublesome bike that,maybe you should get rid

[fzs macdonald]

I changed the hand made brass dog bone from a previous ownerthat gave the bike nearly a 2inch lift back to standard ones. then commuted 30 miles in the wind and rain

[unfazed]

Fixed a slow puncture on the 1000 and went for a high speed run on the 600.

[midden]

I changed the hand made brass dog bone from a previous ownerthat gave the bike nearly a 2inch lift back to standard ones. then commuted 30 miles in the wind and rain

Did it change the ride much?

[brooker81]

Bought Arrow headers. booked in my dyno session for when they are fitted.

[slappy]

Removed the Delkevic exhaust ( now on ebay) because the noise was just a bit too much and put this Micron on and I think it is even louder! I must be getting old.
I will keep this on for a bit because I just like the way it looks.

[Dead Eye]

Definitely one of the better looking FZ1 cans I've seen

[Hedgetrimmer]

Removed the Delkevic exhaust ( now on ebay) because the noise was just a bit too much and put this Micron on and I think it is even louder! I must be getting old.
I will keep this on for a bit because I just like the way it looks.

Getting old = going deaf = can gets quieter! 

Looks nice and tucked in, understated 

[woodwizzard]

Fitted new brake pads to the front and now trying to find a suitable place to mount my little red LED rear fog lights.

[Rexr]

Nice run up to Oban today weather was ok, stopped in Inveraray for a brew on the way back, on the ride back down the road just up from the Dunoon turn off there was a truck coming towards me a big artic truck then the arsehole driving it decides his mobile is more important than keeping his truck on the road, truck veers to the left on to the grass banking at about 40mph, I was doing 60mph and the next thing was a wave of grass, dirt and rocks being scattered all over the road, the bike and lastly me got a lovely bruise starting to develop on my chest fucking legs got it as well.....fucking arsehole drivers leave ya fucking mobile phones alone and look where ur going.......

[kitcrazy]

met me bro in law at aylesbury had a blast to on yer bike in oxford to test ride the ducati diavel then a ride to cambridge and home great day

[mickvp]

Nice run up to Oban today weather was ok, stopped in Inveraray for a brew on the way back, on the ride back down the road just up from the Dunoon turn off there was a truck coming towards me a big artic truck then the arsehole driving it decides his mobile is more important than keeping his truck on the road, truck veers to the left on to the grass banking at about 40mph, I was doing 60mph and the next thing was a wave of grass, dirt and rocks being scattered all over the road, the bike and lastly me got a lovely bruise starting to develop on my chest fucking legs got it as well.....fucking arsehole drivers leave ya fucking mobile phones alone and look where ur going.......

sounds nasty. looked a nice day for a ride out though, I would probably have seen you up there if it werent for the fact I was trapped in work all day 

[brooker81]

All done arrow headers finished remaps tommorow then on the dyno next month.