Date: 30-04-24  Time: 16:52 pm

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - ajhutchinson

Pages: [1]
1
For Sale & Wanted / Fazer 1000 Gen1 Items for sale
« on: 28 August 2014, 09:58:46 pm »
Selling Bike so have decided to have a clear-out. Many items for sale so please PM me so that I can discuss Postage and Payment terms, it’s also going to help me keep track of items sold. I will ensure that postage is kept to a minimum.  Items can also be collected if required.  Items located in Telford Shropshire.


Carbon Fibre Front mud guard with gold coloured mesh inserts Used Ex Conditon  £60.00 (New £50.00)

Carbon Fibre look Rear Hugger (Red Fox) Used Ex Condition  £60.00 (New £50.00)

Carbon Fibre Side panel Over lays (Including black 2 x Side panels) Used Good Condition  £35.00 (New £32.00)

Aluminium Allen bolt kit (Red in colour) New  £25.00 (New £20.00)

Airblade Irdium screen New  £20.00 (New £18.00)

Stainless steel Radiator cover  Used Ex Condition  £50.00 (New £45.00)

Haynes Yamaha FZS1000 workshop manual  Used Ex Condition  £10.00 (New £8.00)

3 x Flat round Yamaha Tuning Fork decals (30mm Dia approx.) New  £2.00 or 75p each

2 x Genuine Yamaha Flat Name decals (50mm in Length approx.) New  £2.00 or £1.25 each

3 x Genuine Yamaha Gel round Tuning Fork decals (25mm Dia approx.) New  £4.00 or £1.50 each

Please use the link below to see pictures of all items (Hopefully)
http://s1378.photobucket.com/user/hutch_chrissie/library/?sort=3&page=1


2
Fazer 1000/FZ1 corner / Engine Paint
« on: 01 May 2014, 09:56:13 am »
Hi to all, got a problem with he engine paint in the fact that it is starting to flake off.  The bike is a 2002 model with silver engine.  My question is there a make of paint out there that is a good colour match in aerosol form ie from Halfords.

3
For Sale & Wanted / Clutch cover Gen 1 wanted
« on: 26 January 2014, 02:01:21 pm »
Need replacement clutch cover for Fazer 1000 Gen1 in silver would be great, but would consider black.  Bike blown over in heavy winds yesterday and crack cover.

4
Fazer 1000/FZ1 corner / Bike blown over in high winds today
« on: 25 January 2014, 06:16:50 pm »
Today in the high winds my bike a Gen1was blown over. Damage to the bike, 1 bar end, Clutch cover cracked (swing slight oil leak) and possible bent bars, all on the right side. Lucky no damage to fairing or tank.  Could have been worse. If anyone has any of these damaged parts that they wish to sell, please either PM me or call 07717312020. 

5
Fazer 1000/FZ1 corner / Motografix
« on: 19 July 2012, 06:37:37 pm »
hi to all, has anyone on the forum fiited these Motografix number boards to there bike.  Are they worth the money, easy to fit??  Pictures of your bike would also be helpful.
Thanks for reading
Hutch

6
Fazer 1000/FZ1 corner / Front discs need replacing
« on: 11 July 2012, 02:49:46 pm »
Hi all, Front discs need replacing on my Gen1.  Seen many types and manufactures on Ebay, been looking at the ones from Hongkong, but unsure of the quality.  Has anyone on the forum tried them and what did you think??  If not does anyone have any suggestions has to where to get a set from at reasonable cost, dont have a large budget.  All help on this matter greatly appreciated. Many thanks for reading. Hutch

7
Fazer 1000/FZ1 corner / Rev Counter Pulsing to 9k rpm
« on: 29 March 2012, 12:07:08 pm »
Hi all just tried to start the bike after its winter lay up.  Tried to start it and all I got was the starter relay chattering and the Rev Counter going from zero to 9k and back again, have seen this before but only to 7k and this beening the exup valve. 
 
Any idea what the 9k means??????????
 
thanks for reading..

8
Fazer 1000/FZ1 corner / R1 front-end
« on: 26 September 2011, 09:05:11 pm »
Hi to all, first post on this new forum site.
 
Just finished my R1 front-end conversion using 5PW forks and yoke.  Took it out for a quick blast and found the front end a little soft, so need to do some adjustments. 
 
What I'm after is, does anyone know the standard settings for both preload, compression and damping for this model of R1

Pages: [1]