Date: 29-03-24  Time: 07:40 am

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Andrew

Pages: 1 ... 3 4 [5]
101
The Laboratory ! / Re: TTeesttttinnngg
« on: 30 June 2011, 10:50:58 pm »
 :rollin

braw fae = good from, fine from, great from etc

102
General / Re: New site
« on: 30 June 2011, 10:37:25 pm »
 :2guns

103
General / Re: Are we in full swing?
« on: 29 June 2011, 11:03:08 am »
 :woot :guitar

104
The Laboratory ! / Re: Embed
« on: 16 January 2011, 10:31:55 pm »
or not  :b


 

105
Messages for Users / Re: Andrew
« on: 12 January 2011, 07:10:07 am »
Alright, ta. There doesn't seem to be a problem, clicking log out through the wiki logs out the forum account too but it's no issue. I'll do some more of the wiki tomorrow and i'll let you know if it causes any issues.

106
Messages for Users / Re: Farjo
« on: 06 January 2011, 08:19:45 pm »
Aha! Worked it out. Should work fine now (i hope :P)

107
Messages for Users / Farjo
« on: 05 January 2011, 08:35:31 pm »
On the wiki, i've left some Attn notes on the main page, basicly on the hot poop on foc-u the headings with the Attn's are just links to the main sections about it. What do you want done about those?

108
General / Re: Got some questions
« on: 04 January 2011, 07:44:14 am »
Yes there's no link back yet. Also most of the pages have not been copied across, just the battery one - a job for a volunteer!

I'll do it if you want, then that would leave John, Aegis and Mike to do the stickys. They seem to enjoy doing it.

BTW, from the main foc-u page, the hot poop link doesn't work. It's not being found on the server..

109
General / Re: Testing...
« on: 04 January 2011, 07:39:19 am »
The only way I can think of about moving post count, custom titles and join dates would be to edit folks profiles manually, 1 by 1.

Would be helluva job.

110
General / Re: Someone's stolen the front page
« on: 04 January 2011, 12:17:03 am »
Works for me?

111
FZS600 / How to Balance your carbs
« on: 03 January 2011, 07:08:23 pm »
Originally posted by pointer2null

The following instructions relate to a MK1 1998 Fazer, other models may be slightly different but the principle is the same.

 
 This is a guide, if you break it, burn it, scratch it, blow up your garage/bike/cat or do yourself any injury then that's your problem!
 
 Some of the tools needed:
  • Long Philips or pozidrive screw driver (to adjust the carbs)
  • 8mm socket (to remove the tank)
  • 10mm socket
  • 5mm Allen key (to remove the tank)
  • Security torx driver to fit the TPS
  • Pair of pliers (to remove the clips on the various pipes etc)
  • Small torch (not essential but damn useful)
  • Carb balancer (I'm using a Morgan)
  • Couple of rags

 The Morgan Carbtune - cost about £50 and well worth it.
 
 You can get them here www.carbtune.com
 
 First of all two notes on safety:
 
 You will need to disconnect and reconnect the fuel tank, petrol is highly flammable and the vapour is explosive in the right conditions. The vapour is heavier than air and can easily collect in an enclosed space. Do not smoke and be very careful to ventilate the area.
 
 You will need to run the engine during the procedure and exhaust fumes are highly toxic. Carbon Monoxide from exhaust fumes is a colourless odourless gas and breathing it will quickly lead to unconsciousness and death. Make sure you work in a well ventilated area or outside. If you are working in a garage you need to take special precautions to prevent a build up of toxic gasses
.
 
 I have an exhaust extraction system in my garage:
 
 
 
 Before starting this ensure that the tick over is set correctly, the air filter is clean, the spark plugs are clean and have the correct gap.
 
 Strictly speaking you should also check your valve clearances, but that is a big job. When I do it myself I will make another HOWTO and post it here.
 
 1) put the bike on it's centre stand and make sure it is stable and not going to fall over.
 2) Next we need to check the setting of the throttle position sensor (TPS)
 3) Switch on the ignition and disconnect the TPS plug, then reconnect it. This puts it into setup mode. The rev counter will now display 0RPM, 5000RPM or 10000 RPM.
 
 
 
 4) If it is showing 0 or 10000 loosen the two security torx screw slightly - just enough so that you can move the TPS housing, but no so much it moves on it's own.
 
 
 
 5) Twist the TPS housing so that the rev counter reads 5000
 6) Tighten the TPS torx screws taking care not to disturb the unit. Switch the ignition off.
 7) Remove the seat
 8)Using the 8mm socket remove the small bolt at the front of the tank just behind the handlebars.
 
 
 
 9) Using the 5mm Allen key loosen the Allen bold at the bottom of the tank.
 10) You can now partially lift the front of the tank, the rear bolt will act like a hinge.
 11) Underneath you will see 3 rubber pipes connected to the tank, a wire and the fuel tap. Two of the pipes are breather tubes and the other largest one is the fuel pipe. The wire is the fuel gauge sensor connection.
 
 
 
 12) Turn the fuel tap to the OFF position.
 13) Using the pliers remove the clips on the two small pipes - the breather tubes, then pull the tubes off the tank itself. Next the fuel pipe - it is a good idea to place a piece of rag under it as there is always a bit of fuel in the pipe that will run out.
 14) You can lift the tank a bit more and disconnect the fuel gauge wire.
 
 
 
 15) Lower the tank and completely remove the Allen bolt from the bottom. The tank can now be lifted off and put somewhere safe.
 16) Next you need to displace the bar that holds the coils and the fuel pump to allow you access to the carb adjustment screws. Remove the two 10mm bolts on either side of the bar and move it back as far as it will go.
 
 
 
 17) Replace the seat
 18) You can now place the tank on the seat back to front - this will allow you to reconnect the fuel line.
 
 
 
 Turn the fuel tap on.
 
 
 
 19) Remove the vacuum port covers on each of the carbs. Numbers two and three are tricky as there isn't much space.
 
 
 
 
 
 
 20) Connect your Carbtune or other vacuum gauge system to the vacuum ports. (If you only have a two way unit, just connect cylinders 1 & 2 first. Then you can repeat the process with 3 & 4 then finally 1 & 4 - remember to put the vacuum port covers on the cylinders you are not measuring!)
 
 
 
 You should now have the Carbtune connected, the fuel tank on the seat and connected all ready to go.
 
 21) Start the bike. Allow it to run for a few minutes to warm the engine. When it will tick over normally we are ready to start.
 
 The four carbs on the bike are linked via a shaft. This shaft has three adjustment screws on it. The one on the left side of the bike adjusts carb 1 relative to carb 2. The screw on the right hand side adjusts carb 3 relative to carb 4. The centre screw adjusts carbs 1 & 2 relative to 3 & 4.
 
 This is where the torch comes in handy - they are not easy to see (you'll find the right hand (as sat on the bike) screw the worst).
 
 Diagram as seen from front of bike
 
 
 
 
 
 
 This is an out of balance reading, yours maybe better or worse.
 
 
 
 
 22) Start by making a small adjustment to the left hand screw. After each small adjustment, remove the screwdriver and blip the throttle a few times. You will have to repeat this process a number of time until the vacuum on carbs 1 & 2 reads the same.
 23) When carbs 1 & 2 are balanced, repeat the process with carbs 3 & 4 using the right hand adjustment screw.
 24) When 3 & 4 are balanced use the centre screw to balance 1 & 2 with 3 & 4.
 
 Don't be surprised if you have to repeat steps 22 to 24 several times.
 
 When you are done the Carbtune should look like this.
 
 
 
 Tip: sometimes the carbtune can stick a bit - taping it will allow the indicator rods to settle.
 
 The maximum difference you are allowed is 10mmHG (about 2 1/2 lines on the Morgan, but you can get it much better than that).
 
 When you are happy with the balance, switch of the engine and the fuel tap.
 
 25) Disconnect the Carbtune and replace the vacuum port covers.
 26) Putting everything back is a reversal of the process you followed taking it all of.
 27) Repeat steps 3 to 6 to reset the TPS.
 
 Two things to REMEMBER TO DO:
 
 1) Turn the fuel tap on after refitting the fuel pipe
 2) Make sure the breather hoses are routed correctly and not crushed or kinked under the tank.

Video:
motorcycle carburetor balancing- Carbtune



112
The Laboratory ! / Re: Scots only folder
« on: 03 January 2011, 05:38:28 pm »
Yep I added a pic :woot

113
General / Re: Testing...
« on: 02 January 2011, 10:07:13 pm »
I attempted to copy a sticky over. I was mostly done then when I hit preview it said that make sure you're connected tot he server bs. I then, without thinking refreshed the page and lost it all, rofl. I'll copy some over tommorow.

114
Your Suggestions and How you can help / Re: List of stickies
« on: 02 January 2011, 09:10:30 pm »
Whey, it works now. Ta for the effort

115
Well that explains why I couldn't upload to the gallery :pokefun

116
Your Suggestions and How you can help / Re: List of stickies
« on: 02 January 2011, 08:10:25 am »
I can get to Gallery/Articles fine but just can't seem to work out how to upload.

117
The Laboratory ! / Re: test
« on: 02 January 2011, 07:55:52 am »
Yea.
Only one annoying thing is when replying either with quick reply or normal, when you post it takes you out of the thread and into a section.

test

118
Your Suggestions and How you can help / Re: List of stickies
« on: 01 January 2011, 11:58:32 pm »
I ment is Articles where they have to go to if I decide to transfer any :lol

119
The Laboratory ! / Re: test
« on: 01 January 2011, 11:24:10 pm »
The thread preview thingy is quite nifty

120
Your Suggestions and How you can help / Re: List of stickies
« on: 01 January 2011, 11:04:57 pm »
so have all stickies to be put into Articals?
And how the foc do I put pics into the Articals gallery?

121
The Laboratory ! / If I make a thread here...
« on: 01 January 2011, 10:57:59 pm »
Will it appear on the front page?

I hope not..

122
General / Re: Testing...
« on: 01 January 2011, 10:46:13 pm »
Folks on here have more posts than I do on the old board :D

Pages: 1 ... 3 4 [5]