This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Messages - Trebus
Pages: 1 ... 14 15 [16] 17 18
376
« on: 17 April 2018, 10:36:40 pm »
Maybe invest in one of the cheap solar chargers. I have one and they do work to keep a battery topped up.
377
« on: 17 April 2018, 10:34:47 pm »
Don’t take it personally, these guys are only expressing an opinion. That of course is why we have a forum, so anyone can contribute. From the looks of it I’m sure you’ll get a buyer.
378
« on: 17 April 2018, 07:46:17 pm »
Even better, lift the dust seals around the corner and dry it completely. It will be fine I’m sure.
379
« on: 17 April 2018, 12:59:18 pm »
Also check the drain holes are clear, they could be blocked.
380
« on: 16 April 2018, 06:27:27 pm »
Check your air box, they love nesting in them!
381
« on: 10 April 2018, 12:35:50 pm »
😂😂
382
« on: 10 April 2018, 12:31:57 pm »
Yep 😂
Honda actually refer to them as ‘winkers’ in some of their old microfiches too 😀😀
383
« on: 09 April 2018, 09:01:04 pm »
Double post!
384
« on: 09 April 2018, 08:59:13 pm »
Cheers Fazersharp, much obliged!
385
« on: 09 April 2018, 08:22:21 pm »
Looking good! What compounds and mop heads are you using to achieve those results? Have got a small bench grinder but never had a go at polishing with it. Normally just go by hand with Autosol and finish with Belgom Alu.
386
« on: 09 April 2018, 08:16:59 pm »
You could always smear a bit of filler in there and get a paint touch up bottle mixed up. I’ve taken plastics into a local paint shop and they’ll mix some up with a little brush for about £5. Or find the paint code and order online.
Edit, I see you’ve already got touch up! One other suggestion is a bit of thin aluminium behind the crack to strengthen it and use some more adhesive.
You see that kind of damage on loads of bikes where the winkers got through the fairing, I prefer older methods where they are bolted onto a proper bracket which normally only sacrifices the winker and easy replacement.
387
« on: 09 April 2018, 12:22:51 pm »
388
« on: 03 April 2018, 10:31:23 pm »
Good luck whichever bike you go for. You have some beautiful scenery on the West cost of Norway if a little wet, I love it there 😀
If you’re heading to mainland Europe I would recommend going to the Harz mountains in Germany, superb biking roads.
389
« on: 29 March 2018, 08:48:34 pm »
Can’t help with a photo but one way to stretch the spring is to put washers / coins between each coil. Or the other way I use is locking wire doubled up and pull on using pliers. Either way be careful not to trap your fingers!
390
« on: 25 March 2018, 09:27:35 pm »
Finally finished my R1 fork conversion! Bike been on the ramp for about 5 months 🙄
Mot next week I hope and ready for the new season, lovely weather today
391
« on: 24 March 2018, 09:59:22 am »
I’d be tempted to report it to the police either way, just covers you a bit in case you have difficulty with them.
392
« on: 23 March 2018, 08:18:33 pm »
Beautiful! Good luck with the new bike
393
« on: 23 March 2018, 08:17:42 pm »
Glad to hear you’re not injured, that’s the main thing
394
« on: 21 March 2018, 06:08:30 pm »
The bonded seals or Dowty washers are a good alternative and mean you can re-use them. Copper washers an be annealed and re-used too
395
« on: 17 March 2018, 07:46:27 am »
14.2V at 2.5k RPM sounds good to me without referring to the manual. If you have the lights on when testing it is normal for the voltage to drop at idle. As long as the voltage picks up when you increase the revs you should be good. Also make sure all connections to the stator and Reg/Rec are nice and clean as high resistance will cause problems.
396
« on: 14 March 2018, 05:25:32 am »
I was cycling in Devon a few years ago and some cretinous individual thought it would be a good idea to throw a large takeaway cup of fizzy pop out of their car window as they passed me. Think I would have preferred spit.
Back on topic, Carragher shouldn’t have reacted with those actions but the bloke filming him is a complete wanker. Filming whilst driving, if he doesn’t get done it’s an injustice.
397
« on: 09 March 2018, 10:32:02 pm »
I’ve got a front wheel if you’re stuck? Came off an R1 but it’s the same as a Fazer I think. Surplus to requirements. Slight thread hijack!
398
« on: 09 March 2018, 10:29:35 pm »
PM sent
399
« on: 06 March 2018, 06:37:49 pm »
I’ve had success with Plastic Padding chemical metal repairing an old CX650 tank. Might get you out of a bind.
400
« on: 02 March 2018, 07:25:14 am »
Nonfango stopped manufacturing for a while but looks like their website is running so might be an option. The old stuff was pretty good in my experience.
Got Givi E21 on mine with the PL racks but also have some old school Krauser boxes in stock which are bigger and might be grafted on at some point if life allows any garage time 😀
Pages: 1 ... 14 15 [16] 17 18
|
Show Posts
