This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Messages - Ben600
26
« on: 15 March 2014, 11:10:54 pm »
Have you a pic of the back of the can please?
28
« on: 19 August 2013, 11:44:36 pm »
Hi all! I am looking to make a comeback to Fazer ownership after my beautiful Fazer met a rather sticky demise last October  I am going to be in the market for a Fazer in the £1000- £1500 possibly £1700 margin. What would this money fetch Fazer wise? my last one ended up costing the best part of 2.5k after finance interest etc was factored in, but that was absolutely mint with 15k on the clock? i am assuming I wont fetch such a bike in this price range? Cheers, ben
29
« on: 20 June 2013, 07:13:47 pm »
Putting the feelers out to gauge interest in my FZS600 engine and or carbs.
It's done about 25k miles and has very light damage to the left case which is purely aesthetic, and does not affect the engine in any way.
Please post below or pm any offers if interested.
Many thanks,
Ben
30
« on: 27 March 2013, 04:04:06 pm »
Mudguard available,
I am unsure of the whereabouts of the extender, though I shall look tonight.
There wasn't an underbrace when it was removed., it mounts via 2 bolts either side
I removed it to fit a rather tasty Carbon one from a Ducati
31
« on: 26 March 2013, 10:46:46 pm »
Stand sold. Link pipe(s) sold. all remaining at the weekend will be bunged on ebay!
32
« on: 24 March 2013, 10:31:14 am »
I measured it at 36cm  now it's being ripped apart to help make a can for my ducati!
33
« on: 23 March 2013, 11:31:09 pm »
I'm not 100% sure off the top of my head... I will measure it up to Tomorrow mate . I think it was about 35cm.
34
« on: 23 March 2013, 03:58:48 pm »
I have PM'd you mate
35
« on: 22 March 2013, 10:21:00 pm »
the best quick fix I came up with for a blowing silencer / link pipe joint was to cut a coke can, roll it up and use it as a gasket between silencer / link pipe. Works well, looks ok (can't see it) and is cheap and easy!
36
« on: 22 March 2013, 06:31:31 pm »
Unfortunately the pegs were ruined all these parts were removed before the crash... As for the stand, I will get a quote for postage and get back to you later this evening
37
« on: 20 March 2013, 03:33:39 pm »
One of my chopped cans It's as easy as you like to chop or assemble them and do a god job of it, I've made some for my show winning Ducati's too
38
« on: 20 March 2013, 09:40:07 am »
I ran scorpion cans. Fantastic value, even better noise when I got bored, I chopped them down.... making your own is the way forward!
39
« on: 18 March 2013, 09:49:10 pm »
New they'r 45 quid, so i'd be happy to let one go for about 15quid with P&p...
40
« on: 18 March 2013, 04:40:13 pm »
I will do as soon as I am home mate, away with buisiness today until tomorrow evening.
41
« on: 18 March 2013, 12:36:56 pm »
I ran the Supermaxx sports on my Fazer, which are a fantastic tyre, Until i changed to Pirelli Diablo Rosso II 's which are amazing in wet and dry! they grip like sh1t to a blanket go for them, you wont regret it
42
« on: 18 March 2013, 09:04:59 am »
Ben was too tired.. should have been 40mm / 4cm . ground clearance wasn't affected really and I loved it.
43
« on: 18 March 2013, 08:59:34 am »
Oh, well it said it sent :/
Anyway, It was to say I have a pair in good condition if your interested?
Dont know what theyre worth so PM me an offer?
44
« on: 17 March 2013, 10:07:04 pm »
I ran a 120 front on my FZS600, I found it paid to drop the forks through the yokes by about 50mm. I much prfer the 120 fron, and the reason being it makes for a nice ride and less chance of rolling off the edge of the tyre (as I did on a 110).
45
« on: 17 March 2013, 10:01:37 pm »
PM'd you mate.
46
« on: 17 March 2013, 09:41:32 pm »
I Believe so mate, they carry the stop for the center stand, and I think it is a 52mm end for pretty much any can to fit. The two I have are identical, i bought one to experiment with but never got around to doing it.
The link pipe is as below (not mine, but exactly the same)
47
« on: 17 March 2013, 09:15:55 pm »
sorry mate, the last spare can went on on my my Dukes.. and the Fazer's got trashed.. I have got a standard in the garage somewhere, and 2x aftermarket link pipes?
48
« on: 17 March 2013, 05:35:16 pm »
These are the handle bars. Standard issue Fazer bars, with bar ends. Bars are perfectly straight and were removed because i wanted lower ones. Bar ends, one is scuffed. I did it moving the bike into the garage on the wall the other is perfect. I would be willing to sell complete or separately. Make me an offer on the bits as a lot or individually, I don't mind. I amin Wisbech near Peterborough if you wanted to collect. or as previously said, I can post at your expense. i'd be happy with cash or PayPal. PM me or reply on this thread to contact me, alternatively drop me a text :07585157885 regards, Ben
49
« on: 17 March 2013, 05:31:00 pm »
These are the centre stand pics...
on the whole it is very good condition, as you would expect some chips and minor rust marks due to its location on the bike. Mounting lugs are perfect and the spring will be supplied as in pics.
Took off the bike as it was heavy and in my young stupid mind, I thought it looked best without. It didnt, and was highly impractical without!
50
« on: 17 March 2013, 05:27:44 pm »
Attached are the photos of the panel, its a left side. It has two minor imperfections, one by the holes for the grab rail (see yellow circle) , which look to be from panniers rubbing, the second by the light which is a very minor scuff that has been touched in and is barely noticable
|
Show Posts
