This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Messages - 72 chamb
1
« on: 04 March 2016, 05:28:33 pm »
I agree with grizzley. ..seat that I got from him was spot on...
2
« on: 30 October 2015, 07:48:27 pm »
Bit of a polish after a wet day...
3
« on: 19 June 2015, 10:32:39 pm »
Yes fitted them and had no problem...i took the old ones from the crash bungs to a pllace near to me.they couldn't give me the same thread but i havent had any issues. ...
4
« on: 06 June 2015, 09:35:00 pm »
5
« on: 06 June 2015, 08:37:46 pm »
It doesn't have gel insert
6
« on: 06 June 2015, 08:36:22 pm »
Yes and he has said he has another that you can have any colour writting..only done 30 miles and no problem..and no slipping forward..
7
« on: 06 June 2015, 08:15:06 pm »
Just got this one and is very comfortable... £100 delivered.
8
« on: 01 June 2015, 07:06:54 pm »
I did the headlight mod last week...all the bits from halfords and cost me about a tenner..it took 30 mins to do and is alot better..
9
« on: 24 May 2015, 07:39:25 pm »
I got mine yesterday at my yam dealer at 45p each
10
« on: 18 February 2015, 06:14:30 pm »
Thats brilliant....thankyou
11
« on: 17 February 2015, 09:07:35 pm »
Do you know what length they are as the ones for the cras bungs are far to long.
12
« on: 17 February 2015, 05:30:49 pm »
I'm fitting a new belly pan to 2000 plate 600.. i need to use the engine mounting bolt but when i bought the bike it had crash bungs on it. I have took these off but do not know what size bolts to replace them as the crash bungs needed longer ones..
any tell me size and length needed..
Thanks
13
« on: 06 December 2014, 05:12:42 pm »
Very nice...where did you get it from...
14
« on: 13 October 2014, 06:31:59 am »
I had one cut locally in notts. He had blanks in for yamaha. Cost about a fiver a worked fine...
15
« on: 06 October 2014, 06:40:36 pm »
New one painted and no stickers are £170.yamaha dealer..i understand deefer fixes them as well
16
« on: 26 September 2014, 05:21:05 pm »
I had scuffs on my mirrors and used different grade wet and dry paper until smooth..i used boot poish to colour and shine...ill find a picture. .
17
« on: 17 September 2014, 10:04:31 pm »
Yep K&N next.....do i need to adjust anything on the engine side of thing.....not for making it quieter but mixture or anything. .
18
« on: 17 September 2014, 09:21:01 pm »
No.. as you say its probably due to me being use to standard...also its whether i need to adjust anything.
19
« on: 17 September 2014, 08:30:48 pm »
I've put an ART pro series 2 end can on my bike and compare to original its loud...anyone had experience with this can and do i need to adjust anything.
Thanks..
20
« on: 04 June 2014, 06:30:47 pm »
Hehehe..
21
« on: 03 June 2014, 11:59:06 pm »
Comes with ropes that I have attached to the corners and tied to fence...I have electrical conduit clamps that will screw over the metal frame and anchor to the floor...
22
« on: 01 June 2014, 08:40:49 am »
 | 20140601 080619 |
23
« on: 30 May 2014, 05:31:38 pm »
Just measured mine and they are 6mm x 10mm
24
« on: 23 May 2014, 08:39:27 pm »
Found the perfect solution..a gardman walk in polytunnel. .it has ventilation and room to walk around the bike...perfect fit and all for a reasonable £40 off fleabay
25
« on: 22 May 2014, 12:22:54 pm »
Im keeping my bike outside covered in a bike cover and tarps...im fretting my pride will rust and it will knacker before I get out on it...I dont have a shed or garage to use..
Any suggestions on best practice to prevent damage/rust etc..
Thanks
|
Show Posts
