1
FZS600 Fazer / Re: Squawking noise on and off
« on: 22 March 2019, 04:07:02 pm »Knackered wheel bearing/s?
Speedo drive as mentioned.
What about your lid? Vent open/loose and causing high pitched noise?
Chris
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to. 1
FZS600 Fazer / Re: Squawking noise on and off« on: 22 March 2019, 04:07:02 pm »Knackered wheel bearing/s? Speedo drive as mentioned. What about your lid? Vent open/loose and causing high pitched noise? Chris 3
FZS600 Fazer / Re: SFS Performance coolant hoses can be made to order« on: 21 March 2019, 09:14:44 pm »thats a stunning bike mate Thanks, Taken a long time to get it to where it is but I'm happy with it =) Chris 4
FZS600 Fazer / Re: SFS Performance coolant hoses can be made to order« on: 21 March 2019, 02:33:17 am »A little teaser for you of how nice they look 5
FZS600 Fazer / Re: SFS Performance coolant hoses can be made to order« on: 21 March 2019, 02:22:18 am »Hi All, I set up the original group buy which was successful for these. Thread is called "Rad hoses" if I remember right. They are lasting well and if you can get them then I would say go for it. HOWEVER!!! Be very careful that you are definitely getting a set for the fzs600 and not the later FZ6. All the best, Chris 6
FZS600 / Re: HOW TO: Forks Seals, Bushes and Oil« on: 16 February 2018, 05:44:31 am »Great guide Just done my fork seals and the guide really helped. One of my damper rod bolts had a rounded off head so I had to hammer in a triple square bit to grip it and get it out. I obviously then needed to get a new bolt. I thought I'd post up the part numbers in case anyone else has the same problem. Damper rod bolt part number: 3D8 23181 00 Copper crush washer for damper rod bolt: 509 23158 L0 Hope that's useful to anyone else with the trouble I had with mine. Chris 7
FZS600 Fazer / Re: Renthal 758« on: 19 July 2017, 06:38:48 pm »
So much better than the standard bars. I filed down the tabs a bit and they've been fine =)
Chris 8
FZS600 Fazer / Re: What have you done to your FZS600 bike today« on: 10 June 2017, 06:27:57 pm »
Those pistons you've made look amazing, great job!
Chris 9
FZS600 Fazer / Re: Silicone Radiator Hose Kits« on: 09 June 2017, 02:07:05 am »
Can't remember how much they were last time but it's listed in the original "rad hoses" thread.
They weren't cheap but I'd rather have silicone ones than the standard rubber ones anyway and they look so much better. Chris 10
FZS600 Fazer / Re: What have you done to your FZS600 bike today« on: 03 June 2017, 02:59:43 pm »At least your workmates will know when to put the kettle on when you're leaving home to go to work Hahaha!!! Trust me, there are bikes with much louder exhausts than mine and it's not too offensive, definitely louder though, especially as the revs get higher under load. Chris 11
FZS600 Fazer / Re: What have you done to your FZS600 bike today« on: 03 June 2017, 02:10:31 am »13
FZS600 Fazer / Re: What can be done about my forks« on: 03 June 2017, 01:37:28 am »
That's why you sand them back first
Chris 14
FZS600 Fazer / Re: What can be done about my forks« on: 01 June 2017, 03:38:34 pm »
Sand them back, primer then paint them. I did mine black and really pleased with them.
Chris 15
Introduction / Re: Hello all FZS 600 my 1st bike« on: 28 May 2017, 04:27:22 am »
Looks like it's in great condition!
Welcome along. Chris 17
FZS600 Fazer / Re: Silicone Radiator Hose Kits« on: 16 May 2017, 10:25:55 pm »They should have all the tooling as they have already made 11 sets. Hope it all works out for you as they do look awesome on the bikes. Yeah, I wondered the same. He was really helpful and always replied really quickly to emails. No worries, hope it goes ok for you all. Chris 18
FZS600 Fazer / Re: What have you done to your FZS600 bike today« on: 16 May 2017, 04:38:48 pm »
Put some miles on it!
MOT next week. Not worried about it as it's running spot on. Chris 19
FZS600 Fazer / Re: Silicone Radiator Hose Kits« on: 16 May 2017, 04:36:35 pm »
They should have all the tooling as they have already made 11 sets. Hope it all works out for you as they do look awesome on the bikes.
If you have any question about the first group buy, which I organised, then all the info should be in the old thread but if you can't find something then just PM me. Chris 20
General / Re: Anyone got a chrystal ball« on: 09 April 2017, 09:59:33 pm »
I have a Weise psycho jacket and it's great, leather/textile mix and it's been great.
https://www.google.co.uk/#q=weise+psycho+jacket&spf=381 Chris 21
FZS600 Fazer / Re: Best lube for brake pistons?« on: 26 March 2017, 02:24:25 pm »
Red rubber grease is best if you have some. Are you rebuilding the caliper or just pushing the pistons out a bit cleaning them and then greasing them?
You can use brake fluid but it's not the best and will wash off too easily. Chris 22
FZS600 Fazer / Re: Stainless Downpipes« on: 25 March 2017, 03:32:04 pm »
Pretty sure the later 02/03ish had stainless headers but the welds aren't so they still get holes in the collectors and joins...
Chris 25
FZS600 Fazer / Re: Centre Stand« on: 04 March 2017, 11:41:07 am »
It may have been lowered by a previous owner but think twisted/corroded centre stand is the more likely reason that it's difficult to get up on to the stand.
Chris |