Date: 25-10-21  Time: 22:02 pm

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - king1

Pages: [1] 2
1
General / Re: split crank case
« on: 23 January 2015, 09:28:07 pm »
Thanks for all that
Just ordered one and gasket
hopefully exhaust should not give me trouble as it was onlyfitted just over 12 months ago :)

2
General / Re: split crank case
« on: 23 January 2015, 09:16:06 pm »
yep you are right £30 fleebay for a sump

3
General / Re: split crank case
« on: 23 January 2015, 06:05:15 pm »
pictures of my damage
I have found a replacment engine, bottom only for £30 but don't know how much it will cost to build it from mine :'(

4
General / split crank case
« on: 23 January 2015, 04:45:18 pm »
HELP
 
Like a muppet I got confused when undoing the oil drain plug and ended up tightening it not loosening it.
 
Yes I have split the casing.
is there a fix, or is a new case?
Thanks

5
FZS600 Fazer / Re: front brake switch
« on: 12 January 2015, 01:02:44 pm »
I tried genuin and after market, they are all sh1te
at the moment i have what is left of the last one just danging from the handlebar
i think i will replace it in July for mot

6
FZS600 Fazer / front brake switch
« on: 08 January 2015, 06:55:39 am »
Hi

Has anybody done a mod to the front brake switch, I am fed up of it breaking.
The latest one broke apart from ice

thanks
The latest broke from ice

7
FZS600 Fazer / Re: front brake switch
« on: 23 November 2014, 09:26:40 am »
Hi
After looking at all the other lists on this subject

I have a question, I have just ordered another switch, would drilling a pilot hole in the underside help to drain out moisture and filling it with WD40?
What about wrapping it in cling film?

Are there any other suggestions or mods ?

Thanks

8
FZS600 Fazer / Re: running problems
« on: 18 October 2014, 04:47:26 pm »
Right I am banging my head against a brick wall
I am lucky if I can do 60mph
all plugs sooted up
I am getting no where

is there anyone in the Manchester area who could give me some help or a pillow for the wall

9
FZS600 Fazer / running problems
« on: 17 October 2014, 07:00:54 pm »
My bike is running like a bag of s##te
At normal speeds it is ok but at motorway speeds
the engine is like it is stuttering
no power
power even drops off
you start off with a full fuel tank and it drops down fast, when you open it there is a fair vacuum

at the moment I am tuning in the carbs and building a balancing tool, to check the balancing
all my local garages are not interested in looking at it

What do I need to look at and do???

Thanks
you can tell a happy biker by the flies in his teeth

10
General / Re: Winter glove recommendations? (Don't mention bar muffs)
« on: 14 October 2014, 12:10:10 am »
Silk inner gloves do work
last year I bought a pair of armadillo gloves which help with the cold
as to getting wet, sorry but no idea as I always end up with wet hands when it is raining
this year for the first time ever, I am trying heated gris.

good luck in the hunt
I would be interested to find out how to keep dry hands

11
General / helmet cameras
« on: 11 October 2014, 12:19:10 am »
Hi
I am thinking of getting a helmet camera
what are the sugestions?
Thanks

12
FZS600 Fazer / carbs set up
« on: 04 October 2014, 01:17:26 pm »
Hi
Is there anyone in the Manchester area that can set the carbs up, or know of a garage that can, cheaply
As far as I know they are balanced, just need the fuel mixture setting
Thanks

13
FZS600 Fazer / carb pilot screw
« on: 03 October 2014, 08:50:17 pm »
My bike has been running s##t for a few weeks so have looked at all the usual faults
this time checked all the jet holes and all the pipes, checked the pilot screws and got s###wed
yep the end has snapped off on one of them, can you get new ones???? as I cannot find them anywhere.

14
Events, Meets, Ride outs etc / ride out
« on: 20 September 2014, 07:49:30 pm »
Anyone going to Southport on Sunday?

15
FZS600 Fazer / Re: Stainless downpipes
« on: 15 September 2014, 06:27:39 pm »
I got a set of stainless down pipes from my bike shop and no problems
It was a bit of a b~@"h fitting them, especially on your own

16
FZS600 Fazer / Re: carb inlet rubbers
« on: 13 September 2014, 08:05:55 am »
An update
this morning I noticed that when I rev the engine, black smoke comes from ghe exhaust

17
FZS600 Fazer / Re: carb inlet rubbers
« on: 13 September 2014, 03:18:38 am »
update
just tried running it in my break and no arcing from plug caps

18
FZS600 Fazer / Re: carb inlet rubbers
« on: 13 September 2014, 12:54:29 am »
fuel filter, air filter both ok
fuel tap ok
all pipes ok
I did look at 1 of the plugs and it was ok, could not get the second one out so gave up

I only started all this work cause it was running bad and it is still the same

So I will try to see if rubbers are leaking and if arcing from plug caps

Any more suggestions?

19
FZS600 Fazer / Re: carb inlet rubbers
« on: 12 September 2014, 09:12:55 pm »
Fuel filter is ok
I will try the water to see if they are leaking.
A biker I met today said it might be the ignition coils

20
FZS600 Fazer / carb inlet rubbers
« on: 12 September 2014, 06:57:09 pm »
Hi
I am after some help
My bike is running on kangaroo juice
I have cleaned out tank, cleaned carbs, oil and filter change.

The symptoms and motorway cruising speed it is stuttering, at fast acceleration there is no power and it even slows down.

I have been told it could be my carb rubbers that are leaking as they are cracked,

Could this be the problem, I was going to try sealing them and wrapping tape round them, alternatively new ones are £70.
I have been looking at other topics on the forum but still need help

Any advice

Thanks
Kelvin

21
General / Re: Winter Gloves
« on: 09 September 2014, 07:08:51 pm »
I bought a pair of armadillo gloves with the 2 fingers
they do work, especially with silk inners
to top this off I have just fitted heated grips, to be realy cozy

22
Hi
I need some help on this topic of tyres
I need a set but unfortunately I cannot afford a lot of money
any advise on what to get?
I was looking at nankings, then found out they sre teflon tyres, nonstick.

Thsnks
kelvin

23
Hi two tinz

I'm the guy who was talking to you at mc'ds in Bredbury today

happy biking
kelvin

24
FZS600 Fazer / Re: tyres
« on: 07 April 2014, 12:53:02 pm »
I had to have a valve replaced and the guy said my tyre was getting squred off or something like that, what of an issue is this?
The tread iss ok and I have not noticed anything whilst riding

25
FZS600 Fazer / Re: H1 to H4 bulbs
« on: 27 March 2014, 10:35:17 am »
No it's not
if you look at past posts you will see other people have done this conversion

Pages: [1] 2