Date: 10-04-20  Time: 09:51 AM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - His Dudeness

Pages: [1] 2 3 ... 105
1
General / Re: Auld Foccers Weekly Covid Check in Page.
« on: 15 March 2020, 11:28:49 PM »
 :oops

2
General / Re: Good day out, bad end of the evening
« on: 15 March 2020, 10:30:56 PM »
Was your address anywhere in the wallet? I found one dropped at a bus stop. It had an id in it with an address so I posted the wallet in the letter box at the address. Minus the cash of course. Only joking :lol

3
General / Re: Auld Foccers Weekly Covid Check in Page.
« on: 15 March 2020, 10:18:21 PM »
I cant understand why you have to stay at home. I get that you have to avoid coming into contact with other people but depending where you live that can be quite easy.
 I could comfortably go for a walk around the woods and fields where I live without coming within at least 50 metres of anyone.
And going out on the bike seems harmless enough. Your wearing gloves and a helmet, riding solo and at the worst if you need fuel you go to a pay at the pump and if you need a pee then find a Bush 🤷‍♂️
As with most things it just takes a bit of common sense
I'd say give it another few days and things will become clearer.

4
General / Re: Auld Foccers Weekly Covid Check in Page.
« on: 15 March 2020, 10:09:18 PM »
If you're stuck at home you could use the time to do an online course. Lots of topics on this site https://www.edx.org/  and a lot of them are free to do. Worth having a look anyway. See if there's anything you like the look of


I quite fancy the [size=1.625rem]Introduction to Ci Poems in the Tang and Song Dynasty[/size]
I'll be expecting assignment 1 on my desk by Friday :lol

5
General / Re: Auld Foccers Weekly Covid Check in Page.
« on: 15 March 2020, 07:05:52 PM »
If you're stuck at home you could use the time to do an online course. Lots of topics on this site https://www.edx.org/  and a lot of them are free to do. Worth having a look anyway. See if there's anything you like the look of

6
FZS600 Fazer / Re: Steering head bearings
« on: 13 March 2020, 02:15:40 PM »
I did my steering bearings and it made a huge difference to how the bike felt when cornering, well worth replacing it if it's worn. Getting the lower race out was the difficult bit because it has a very thin area to hit against so you have to have the right tool to get a good contact on it. I tried loads of different things with no success, in the end what worked was a long, thin chisel with a bend in it. The chisel was ruined but it did the job. If you've got the right tool you can get the race out in seconds. If you've not got the right tool you'll be trying to get it out for hours :lol

7
General / Re: COVID-19 AKA Coronavirus - A sense of proportion...
« on: 13 March 2020, 01:54:27 PM »
This is my opinion on it. Basically just stating the obvious but sometimes that gets lost. It's a new flu. The fact that it's new means there's no vaccine for it yet. No vaccine means that people in the high risk category can't protect themselves from it with a simple jab. If you can't protect yourself from it with a jab you have to protect yourself in other ways.

Since it's flu it means you get it through contact with a person who already has it. That contact can be from them coughing and sneezing and then you breathe it in or by the person coughing into their hands and then touching surfaces, then you touch the surface and get it on your hands, if you touch your eyes, nose or mouth it gets into your body. So basically you get it from being around sick people. Without a vaccine the best thing you can do to lower your risk of getting it is avoid people as much as possible. The less people you're around the less chance you have of being around a sick person. So only go out when you really have to like for work or buying groceries. If you're out stay away from areas with lots of people especially closed in areas like buses, trains etc. If you're out, stay away from people who are coughing. Wash your hands regularly especially if you've been out, try not to touch your face with your hands.

Apart from that do all the regular things to keep yourself healthy and keep your immune system working well like balanced diet, drink water, cut down on booze and smoking. Also look after your mental health. If you're avoiding being around people doing social things your mental health could suffer so you have to do things to look after that. Limit the amount of time you're looking at news , all day every day will make you feel worse. Stay away from negative talk on social media or negative videos. Too much of that makes you feel worse. Do more of the things that you enjoy doing like hobbies, reading, music, bikes or whatever you're into too and whatever keeps your mind positive. They seem to be saying that it takes months to create a new vaccine so I think this is going to be with us for quite a while so we need to accept that and change our lifestyle and habits to protect ourselves from it especially if you’re in the high risk category but even if you're not in the high risk category you should do it for the people who are. That would be my take on it but I'm not medically trained.

8
FZS600 Fazer / Re: FZS600 first bike - advice?
« on: 30 January 2020, 05:55:18 PM »
This one looks like a real bargain at £1050 http://foc-u.co.uk/index.php?topic=25891.0

9
For Sale & Wanted / Re: My 1998 Fazer 600
« on: 26 January 2020, 10:16:26 PM »
Sorry mate it’s £1050
Won't take long to sell at that price!

10
Introduction / Re: New member introduction January 2020!
« on: 26 January 2020, 10:09:35 PM »
Nice bike. If you put your questions in the Fazer 1000 section you're more likely to get an answer. Not many people look at the introductions

11
FZS600 Fazer / Re: Front Fairing Decals
« on: 26 January 2020, 09:41:53 PM »
You could get them from Yamaha using the part number in the parts catalogue but they probably cost a small fortune http://foc-u.co.uk/index.php?action=downloads;cat=2

12
FZS600 Fazer / Re: pipes from cam shaft
« on: 25 January 2020, 07:04:05 PM »
While you're in there I'd take the breather off. It's the fat s shaped pipe and check if it's blocked up with emulsified oil. The mayo looking gunk. I think if the oil was ever over filled some can get pushed up into the air box and it turns to mayo and blocks the pipes.

13
FZS600 Fazer / Re: Help Repairing My Beloved FZS
« on: 23 January 2020, 09:46:02 PM »
Thanks for that.  That's presently unscrewed from the casing but still connected to the wiring harness.  Would this prevent it starting?  I guess it's not earthed as I've got it.
Yea without the pickup coil there would be no signal sent to the ignitor to tell it when to fire the spark plugs so no spark. It has earth. It has two wires one is earth the other one is the signal wire back to the ignitor. It needs to be bolted into the engine cover to create the signal at the right time as the rotor spins past it

14
FZS600 Fazer / Re: Help Repairing My Beloved FZS
« on: 23 January 2020, 08:33:09 PM »
The pickup coil is beside the stator. It has a white dot on it in this picture.


15
FZS600 Fazer / Re: Carb problems or is it something more?? Fazer 600
« on: 23 January 2020, 08:24:57 PM »
The butterfly's being open more will increase the Hg reading, these should only be open when the throttle is twisted.  With the throttle fully home the Hg reading is set via the pilot circuit only, each must be between 230- 250mmHg at between 1150 - 1250rpm, if the reading is too high the butterfly isn't in it's rest position.  This could be due to a number of factors, bad assembly, worn/broken part/s or incorrect previous carb balancing.


I my experience most owners and many stealers don't know how to balance crabs, they go straight for the butterfly screws when it's the pilot circuit that's the issue.  As I stated unless they're all pulling min/max of 230- 250mmHg with the butterfly's at rest you're wasting your time.   The other real big mistake onwers/stealers make is moving the TPS, this is set at the factory and it doesn't move (unless it's faulty) in operation it's a datum.  They test it, it's reading over/under and they move it, that's it the datum is moved, the reason it's out (and it only works on the one carb No4) is because the butterfly/linkage has moved/worn, so no longer aligning with the datum.  It's the butterfly/linkage that needs bring back to the datum, by resetting them, i.e. level of Hg, then balance all the others, 4-3 then 1-2 then 1-2 & 3- 4.   Just about every TPS has been moved and in my experience just about every bike I've worked on the carbs are out of balance!               
Great info thanks! I thought the vacuum in the intake manifolds would be strongest when the butterfly valves were closed that's why I said his butterfly valves might have been slightly open. Guess I had it backwards :lol One more question when you're doing carbs do you set the mixture screws first using the reading on the vacuum gauge, then balance the carbs using the balance screws?

16
FZS600 Fazer / Re: Carb problems or is it something more?? Fazer 600
« on: 22 January 2020, 06:53:43 PM »
If the engine is only pulling 150Hg there's something very wrong with the pilot circuit probably the screw setting.  Unless you can get the intake vacuum between 230 - 250mmHg you're never going to set the carbs up correctly and the bike will run like a dog.


I suggest you recheck each carb and what you've or I think you said mate put in and how.   
Gnasher I know at idle its the pilot circuit and mixture screws that have the biggest effect at idle but if the butterfly valves where open more than they should be from an incorrect carb balance could that be another reason for lower mmHg readings?

17
FZS600 Fazer / Re: Help Repairing My Beloved FZS
« on: 22 January 2020, 05:41:11 PM »
I'd go for good used parts off ebay but you can get genuine parts here https://www.fowlersparts.co.uk/

18
General / Re: 3 things that make a relay look factory fitted
« on: 21 January 2020, 10:04:34 PM »
Yea good quality electrical connectors aren't cheap but as you say if you make the investment and buy a box you should have them for life. Soldering isn't cheap either. You need a decent soldering iron with a bit of power, good quality leaded solder, rosin flux, cleaner for the iron tip and heat shrink. It all adds up but it's a good skill to have if you can repair wiring :D I'd like to get a really nice crimper tool for doing the OEM style block connectors. Another tool to add to the list :lol

19
FZS600 Fazer / Re: Temporary lack of power
« on: 21 January 2020, 09:53:30 PM »
That Silkolene stuff smells like alcohol so it's probably mostly just isopropol alcohol the same as darrsi uses. Even with the heater circuit open I wonder could you still have carb icing because it would take a few miles for the coolant to warm up especially on a cold day.

There's an interesting chart on carb icing https://www.flightsafetyaustralia.com/wp-content/uploads/2016/01/Icing-chart-1024x699.png

20
FZS600 Fazer / Re: Temporary lack of power
« on: 21 January 2020, 06:38:13 PM »
I've got a bottle of this stuff. It's supposed to help prevent carb icing. Might be worth a try  https://www.silkolene.com/motorcycle/fuel-additives/pro-fst/

21
General / Re: 3 things that make a relay look factory fitted
« on: 21 January 2020, 05:36:49 PM »
I never would have guessed that was a relay. Looks like a connector. Very tidy install! The solder and seal connectors look very handy too.

22
FZS600 Fazer / Re: Carb problems or is it something more?? Fazer 600
« on: 21 January 2020, 05:22:08 PM »
Are you sure you did the compression check correctly? Did you warm the engine before you did the test? Did you fully open the throttle? Are you sure the air filter is in good condition? Were you cranking the engine with a strong battery? Did you repeat the test with some oil in the cylinders? And what were the results after you added the oil?

I have a bike with low compression from worn rings/cylinders. The symptoms it's showing are it's hard to start when cold, it's down on power and top speed and it has a lot of blow-by into the crankcase. It's hard to start when cold however if you put a little oil in the cylinders it start instantly because the oil is sealing the cylinders and bringing the compression up. After it starts it runs well, it has no hesitation or spluttering anywhere. I think in your case it seems more likely that you had a spark issue after cleaning the engine, then later down the road you had a carb issue and you did some carb work and either it didn't fix the problem or it made the problem worse.

Just so we're all clear what exactly are your current symptoms?

23
General / Re: Puncture repair kits (Roadside)
« on: 18 January 2020, 06:27:19 PM »
These are good.
Only thing you have to be careful of is that over time the glue can go off. It'll be a long time though as it's not exactly something you'll use often unless you're unlucky (like me).


https://www.ebay.co.uk/itm/MOTORCYCLE-CAR-VAN-TUBELESS-TYRE-PUNCTURE-EASY-REPAIR-KIT-TOOL-EMERGENCY/173992819037?epid=695016950&_trkparms=ispr%3D1&hash=item2882c7b95d:g:aaEAAOSwtfpdTwjB&enc=AQAEAAACUBPxNw%2BVj6nta7CKEs3N0qVMnz%2FHqbw%2FO0e7MCScZH%2FmWhVcIKC8lKrJZX7KESoiDWMBJmgn75sGw21vhNakowNewOzo9lGEU7GBX2ZfonJyxw9cOcBc6uS8RujIZOKb3QFuIlXrrKMIviXA7JPaj3cfsVqc6y7yK803hTFgZkd%2BR%2F6V0U1BCD%2BIa4n3xOq5ICpTpCEDS9re3MU2K5%2FLIGkTeTRB1GaO5qbYJnumhGDQtPmzW1ktdD8yj5WZPAUbdww%2BxLUedvdCswJ49AC3lp2M%2BGD66np45B%2FngwTGHVQMxK8f%2BuUTOW0JVbRTljG5Opcqzi0FnH3f6xysbgfQcOkKBkj11PAHd1r5mTisRArCFOAnWE3VllNK8utK5fdE9HEiooCuUXEouDA7jEObdQ0%2Bje1yE0toYgWNOqPwUcH6h8Gv6F1MhSHS29c%2FsqZtQmaRJFUG8RcjPAHciaK7GYsgwVX3KfrnseS2YIh7M4gFI%2F7hxSnISPskOV50cWIjSQW4faCiOYsyqdhPolZJ9BX4F0ueu6IOQRadXq7CFOGTG15PUwHURjnNNmXD3uXncLdiIpExmqOmpw6amuoVLSoTGi3uVY29b%2Fu%2F1ha%2F8S0w2qWWaEjVqHNelsHBcOrVHRwx38irwOcny3VoeJzKBMgbekqQzOxBXj0%2B%2FZ7V%2F7olyFbZBP4QfHif%2B5yHvglp8V1LGUaW0FIiwygDm1VJZ6dQHWwlmrDViAK4%2BDYOSjD7f2U9OHR07SA9AMAELjWEt8laqOR0Msw3p8WsgcQiGMg%3D&checksum=1739928190373dc4d36cdbd74d4ea00bd82c67b7f38b&enc=AQAEAAACUBPxNw%2BVj6nta7CKEs3N0qVMnz%2FHqbw%2FO0e7MCScZH%2FmWhVcIKC8lKrJZX7KESoiDWMBJmgn75sGw21vhNakowNewOzo9lGEU7GBX2ZfonJyxw9cOcBc6uS8RujIZOKb3QFuIlXrrKMIviXA7JPaj3cfsVqc6y7yK803hTFgZkd%2BR%2F6V0U1BCD%2BIa4n3xOq5ICpTpCEDS9re3MU2K5%2FLIGkTeTRB1GaO5qbYJnumhGDQtPmzW1ktdD8yj5WZPAUbdww%2BxLUedvdCswJ49AC3lp2M%2BGD66np45B%2FngwTGHVQMxK8f%2BuUTOW0JVbRTljG5Opcqzi0FnH3f6xysbgfQcOkKBkj11PAHd1r5mTisRArCFOAnWE3VllNK8utK5fdE9HEiooCuUXEouDA7jEObdQ0%2Bje1yE0toYgWNOqPwUcH6h8Gv6F1MhSHS29c%2FsqZtQmaRJFUG8RcjPAHciaK7GYsgwVX3KfrnseS2YIh7M4gFI%2F7hxSnISPskOV50cWIjSQW4faCiOYsyqdhPolZJ9BX4F0ueu6IOQRadXq7CFOGTG15PUwHURjnNNmXD3uXncLdiIpExmqOmpw6amuoVLSoTGi3uVY29b%2Fu%2F1ha%2F8S0w2qWWaEjVqHNelsHBcOrVHRwx38irwOcny3VoeJzKBMgbekqQzOxBXj0%2B%2FZ7V%2F7olyFbZBP4QfHif%2B5yHvglp8V1LGUaW0FIiwygDm1VJZ6dQHWwlmrDViAK4%2BDYOSjD7f2U9OHR07SA9AMAELjWEt8laqOR0Msw3p8WsgcQiGMg%3D&checksum=1739928190373dc4d36cdbd74d4ea00bd82c67b7f38b
I use that style plug. Never had a problem with them. If you look very closely at the picture in the ad, the tool for pushing the plug into the tyre is split at the end so as you pull the tool out the plug is pulled through the gap in the tool and remains in the tyre

24
Nice one for taking the pics ;) Very interesting to see the components inside. Well I think so anyway :lol

25
Don't undo anything only asked out of interest on the off chance that you took some pics during the repair. Thanks for the info

Pages: [1] 2 3 ... 105