Date: 23-02-19  Time: 21:36 PM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - daviee

Pages: [1] 2 3 ... 17
1
FZS600 Fazer / Re: Blue Spot Rear Caliper
« on: 20 February 2019, 06:57:06 PM »
only the fazer 1000 and xjr1300 are a fit the rest will nee major mods to work

2
cleaning the wont make any difference you need to lap them in if they are leaking no easy way

3
could be jetted different for the other exhaust


4
put the other one back on see if it goes back to what it was like if it does the quiet exhaust is fooked

5
might be jetted for the other exhaust , or is it just because its quiet making you think its lost power


6
FZS600 Fazer / Re: Sorry - tyres again!
« on: 13 February 2019, 06:15:17 PM »
i went from pr2s to bt023s as i was get puncture constantly on michelins , tried maxxis and i wouldnt wish them on my worst enemy horrible tyres bt023s are fine i can get my toes down on both sides with confidence as i could with the pr2s just couldnt live wwith the constant punctures with them

7
FZS600 Fazer / Re: Rear shock durability
« on: 09 January 2019, 06:13:58 PM »
62 k they were tired from new look up shock upgrade their are a few mods you can do depending on how tight you are  :lol

8
FZS600 Fazer / Re: Oil pressure switch
« on: 09 January 2019, 06:12:43 PM »
as said its a level light not a pressure light if it comes on top it up slightly with an egg cup full of oil  :lol :lol

9
FZS600 Fazer / Re: Help with wiring up a new headlight
« on: 31 December 2018, 01:50:41 PM »
if it has the switch for a pass light it must work as for 2 h1 lights depends pn the reflector one could be hi beam and one could be low beam either way it has to be e marked and show a proper beam on low and hi beam or it will fail


10
FZS600 Fazer / Re: Road noise back
« on: 31 December 2018, 01:47:15 PM »
if you think its the tyre try taking off the front mudgard off and try it could be the tread causing wind rush through the guard making the noise if it goes away try  altering the height of it odd the tyre i have 023s on mine and never notice any tyre noise

11
FZS600 Fazer / Re: Cylinder head removed
« on: 30 December 2018, 02:15:40 PM »
only way to skim a head properly it getting it machined if its within tolerance  i wouldnt bother if you have to lap thee valves you will probably need to re shim it aswell

12
its not a cable drive its electric


13
FZS600 Fazer / Re: Cam chain tensioner
« on: 28 December 2018, 07:12:50 PM »
thats not how you adjust a manual tensioner you  wind it in by hand with your fingers then when it stops you back it out 1/4 turn its on the ape site who make them

14
FZS600 Fazer / Re: Cam chain tensioner
« on: 27 December 2018, 11:50:54 PM »
unless the original fails then leave alone


16
FZS600 Fazer / Re: Cylinder head removed
« on: 27 December 2018, 07:54:58 PM »
if you can get someone to help you it makes it alot easier to fit the barrels to the the pistons as for the o rings at the bottom of the barrels they should be fine as is

17
FZS600 Fazer / Re: Cylinder head removed
« on: 27 December 2018, 04:46:03 PM »
if the barrels have moved opening up the gasket then replace the gasket , think about it this way if you dont you might get away with it may be , but if it leaks then you have to strip the engine back out and replace both gaskets again  as  reusing a head gasket could cause leaks and then you have to take it out again and replace both agaain see where im going with it do it right do it once

18
FZS600 Fazer / Re: LED Spotlight confusion
« on: 23 December 2018, 07:47:32 PM »
sounds like a bad earth

19
FZS600 Fazer / Re: Engine is out; suggest servicing recommendations
« on: 22 December 2018, 08:28:11 AM »
checking the valves is easy enough get the online manual and go through it that way as for shims you can either get them online ebay fowlers yambits etc but check first as sometimes you can swap about if your lucky but if not use the chart to make sure you order the right size

20
deffo the speedo drive take it out  and re grease  it be careful to put it back in properly or the lugs will break off

21
FZS600 Fazer / Re: Clutch
« on: 18 December 2018, 08:36:09 PM »
600 has the same it has  to be put in the right order look up the manual i will show you how to do it 


23
milliput is good but it would be better either brazed or soldered that how they are made in the first place
 

24
FZS600 Fazer / Re: complete front fairing for boxeye
« on: 03 December 2018, 07:44:11 PM »
depends on condition good would easy get £100

25
FZS600 Fazer / Re: Clutch Cable Adjuster
« on: 21 October 2018, 01:01:33 PM »
they are made so you can adjust them without the  aid of tools so when in traffic and the clutch gets hot you can adjust it


Pages: [1] 2 3 ... 17