Date: 29-03-24  Time: 07:32 am

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Hoppy

Pages: [1]
1
FZS600 Fazer / Re: Leaking Fazer FZS600
« on: 23 January 2016, 11:12:19 am »
best not to taste or put near your mouth or food as toxic

2
FZS600 / Re: KOSO Speedo
« on: 01 August 2015, 04:52:43 pm »
any one know how i can put a message on to all the message board ask for a  members name ?,am i missing something [quote hoppy
i scotched cliped the live from the from the fuse box which came out were the ignition fuse was and ran a wire under the tank and along the original loom. i also used scotch clips to join the indicators, fuel, oil and high beam from the original loom to the koso one and i have made my own ground. only problem i have now is i have attached the rpm wires to the ignition coils as shown in the instructions but the revs aren't showing on the screen.  :'(  i have the same koso as you btw its a db-01.
author=coolhandluke link=topic=17048.msg197119#msg197119 date=1432629225]
i scotched cliped the live from the from the fuse box which came out were the ignition fuse was and ran a wire under the tank and along the original loom. i also used scotch clips to join the indicators, fuel, oil and high beam from the original loom to the koso one and i have made my own ground. only problem i have now is i have attached the rpm wires to the ignition coils as shown in the instructions but the revs aren't showing on the screen.  :'(  i have the same koso as you btw its a db-01.

3
FZS600 Fazer / Re: Had my cam chain done but...
« on: 18 March 2015, 07:28:30 pm »
30000 is not a lot of miles for a Fazer cam chain unless you hammerd it every day  if you have the old chain measure it you will probly find it ok they do stretch but tensioner will take that up at that mileage

4
FZS600 Fazer / Re: Had my cam chain done but...
« on: 18 March 2015, 07:19:24 pm »
Try a stethoscope see if u can locate the noise at it worst ,you can pick one up on eBay  I use one on my bike , you can get close to the noise will give you a clue

5
changing the ignition barrel on my fzs600  need sizes or where I can buy new bolts .i know there snap bolts but happy to fit standard bolt as have alarm and good chains davehopton@hotmail.com any help please cheers

6
For Sale & Wanted / Carb to engine rubbers
« on: 15 March 2015, 12:01:32 pm »
I want to replace the carb rubbers as mine are cracked ,not leaking but while the sun is not shinning  good time to do it anyone have good set of rubbers for sale  davehopton@hotmail.com  Trafford Manchester .cheers

7
FZS600 / fzs 600 ignition barrel
« on: 13 March 2015, 07:21:16 pm »
changing my ignition switch on fzs600 1999 need to sorce snap bolts or bolt sizes anyone help cheers[quote author=Hoppy link=topic=15947.msg187003#msg187003

8
FZS600 / :(sorry it's a 1999 fzs600 ignition barrel snap bolts
« on: 13 March 2015, 07:08:34 pm »
Got a 00 fzs600,all good but upon viewing,rear brake was stiff from sitti up,it hadnt much bite in it and to get some pressure we pumpd the pedal.  BUT TODAY on my careful journey to the garage,i was braking with rear and gearing down..approx 20mph,slowin,then out goes the rear,it fishtaild a few feet before i held on in panick and down she went,any advice or reason? It was very unexpected,i dont understand,perfect rear tyre

9
FZS600 / Re: please help, fazer newbie here :(
« on: 13 March 2015, 07:05:58 pm »
Changing the ignition barrel on my 99 fzs600 bought new barrel nut no bolts with it anyone help with sourcing two snap bolts or I'm happy to fit any bolts that will hold new one ,just need sizes as want to do the job in one hit  cheers ,

Pages: [1]