Date: 21-01-19  Time: 09:46 AM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Mustang

Pages: [1] 2 3 ... 8
1
the avon 3dxms stayed on for 56 miles lol. They are a good touring/ summer tyre, or perhaps a good winter one too if you ride hard..I don't this time of year. Which means they just don't get enough heat in them for me. so ive put bridgestones back on the cb, and if anybody wants the avons with genuinely less than 100 miles on them, seventy quid collected gets them. If ive still got them come april, i'll stick them on the fazer for me and dynspuds run to france, I'm guessing they would be perfect for that..
I’ll have them off you please. I’ll send a pm

2
Fazer 1000/FZ1 corner / Silver frame paint
« on: 29 December 2018, 09:39:16 PM »
need to touch up a couple of parts in the frame, it’s a silver colour, 2001 black panels, anyone have a good paint for the frame I can use?

3
Fazer 1000/FZ1 corner / Re: Yamaha fz1 shock upgrade
« on: 25 December 2018, 12:57:15 PM »
Whoops, can’t read. I bought a used shock and Satan type adaptor from the states off the FZ owners forum. Sold it on the bike though. Only seen one other for sale on eBay, typically just after I bought mine. I do have an brand new set of rearsets for the bike if you interested. I sold the bike before I fitted these.

4
Fazer 1000/FZ1 corner / Re: Yamaha fz1 shock upgrade
« on: 24 December 2018, 07:03:53 PM »
Not sure about the fz8. Most of these mods are for the 01-05 FZS 1000.

5
My Avon storm 3dxms are nearly done after 4600 hard miles. 2mm left in the centre of the rear 2.5mm on the front. Only slipped once on a wet manhole at full throttle. I don’t think that’s bad for less than £150 a pair.

6
Fazer 1000/FZ1 corner / Re: FZ1 Gen 2: handguards/muffs?
« on: 21 December 2018, 08:27:50 AM »
+1 for bark busters storms, using the single bar fixing it allows the end of the guard to collapse against the screen at full lock. Although I made the mistake of pulling the bike onto the main stand with the handlebar and broke this large screen. I now have a narrower screen fittted and always pull on the crash bars to stand it up. I did get these guards for £50 off eBay though.

7
  • The 3D-XM’s worked well in the wet but I never tested the limit,
  • they spun up quite easily over white lines in the wet in a straight line without hardly any throttle.
  • So would you say no oh F*** moments going around corners or leaning over in the wet?
  • hmm, Ive not had a tyre do that in a very long time. And in the wet I am very gentle with the throttle and cant remember the last time that happened.
I might contact Avon and see if there is a time period that they can be returned if they arent suitable.
I’ve had about 4 sets of 3dxms they are very good in the wet, like any tyre if you take the piss with the throttle they will slip but they are my go to tyre. I’ve done a trackday on them as well on my gen 2, were great on a that too.

8
For Sale & Wanted / Re: FZ1 rearsets For sale, brand new
« on: 24 November 2018, 03:55:03 PM »
These are still available, brand new never fitted. Nice quality.

9
Fazer 1000/FZ1 corner / Re: sprocket and stuff
« on: 18 October 2018, 03:56:04 PM »
Thought this was about the rear wheel nut, never mind

10
Fazer 1000/FZ1 corner / Re: Wanted - Standard Gen 1 Handlebars
« on: 15 October 2018, 09:10:27 PM »
I have a set with a tiny bend on them, you can have for free if you want

11
Fazer 1000/FZ1 corner / Re: sprocket and stuff
« on: 14 October 2018, 02:31:40 PM »
If you still have the toolkit there’s usually a spanner to fit the back nut. Will do if you mark where it is the start then count turns off.

12
Fazer 1000/FZ1 corner / Re: Headlight volts drop
« on: 12 October 2018, 09:41:23 PM »
If its a gen 1, these are notorious for
  • having undersized cables in the sub-loom, sits under the front cowling, connects to the main loom.
  • the same undersizing on the cables going from the reg-rec to the main loom.
My FZS had a similar issue in that the volts at the clocks was sitting around 10v with the headlight on, I go around this issue by running an extra ground to the clock from the small frame mount above the reg-rec. Then I changed the halogens for LED -
I went for a fanless design because rain would just kill a little fan in now time, and where the shaft behind the bulb is the exact same width and length so the rubber headlight boots seal against them keeping the headlight sealed.

These LED bulbs have several benefits over HID but primarily you get proper hi beam and with a much better low beam pattern.
Thanks for your reply, I suppose it’s just easier to fit the leds

13
Fazer 1000/FZ1 corner / Re: Headlight volts drop
« on: 10 October 2018, 06:43:11 PM »
Thanks mate, I’ll carry out a Few checks, the bike already has relays I’ve discovered same as the r1.

14
Fazer 1000/FZ1 corner / Headlight volts drop
« on: 09 October 2018, 09:18:16 PM »
i notice when I switch my lights on sometimes the clocks go off then come back on, also if I pull the pass light switch in. I did a test with the lights disconnected and that stopped the clocks going out. I’ve checked the battery voltage and it drops quite a bit when the lights go on, I guess it’s enough to cut the clocks out. Has anyone altered their lights to fire them off a relay? Would it make any difference? Gen 1 2001

15
Fazer 1000/FZ1 corner / Re: New Exup cable failed
« on: 26 September 2018, 09:34:44 PM »
New cables arrived form brooks barn motorcycle, different design. Exhaust end cables go right through nipples. Other end look pressed on.

16
Fazer 1000/FZ1 corner / Re: New Exup cable failed
« on: 26 September 2018, 09:33:08 PM »
Mine snapped when I was rear ended and the exhaust was shunted forward.  I replaced the inners with the venhill rebuild kit, about £10.  Did 30 k or so before selling it and are still on now so they are decent.
Was an option but as I am hopefully get a refund on them I’m just as well getting a new set.


17
Fazer 1000/FZ1 corner / Re: New Exup cable failed
« on: 26 September 2018, 09:31:57 PM »
Mick has a used one for sale here http://foc-u.co.uk/index.php/topic,24571.0.html

I would sooner a used OEM than a new snide. Just my thoughts.

I would rather have new cables. They don’t last forever and pattern parts can be as good as .

18
Fazer 1000/FZ1 corner / Re: New Exup cable failed
« on: 26 September 2018, 09:28:52 PM »
Slinky glide from wemoto
Did you contact WeMoto about it, they can very good about replacing stuff that may be faulty.
Yes I asked them and I will return it.

19
Fazer 1000/FZ1 corner / Re: New Exup cable failed
« on: 25 September 2018, 04:18:10 PM »
Slinky glide from wemoto

20
Fazer 1000/FZ1 corner / New Exup cable failed
« on: 24 September 2018, 03:59:29 PM »
I bought these cables a few months ago not done many miles and the nipple has just pulled off the cable.

21
For Sale & Wanted / Re: Brand new fzs1000 fairing garage clear out
« on: 10 September 2018, 09:47:40 PM »
I’ll have the fork springs if they’re progressive type?

22
Dunn & Bradstreet .?

23
For Sale & Wanted / Re: FZ1 rearsets For sale, brand new
« on: 17 August 2018, 09:48:21 PM »
Bumping

24
One on eBay 99.
£
292680168737

25
Fazer 1000/FZ1 corner / Re: Exup again 🧐
« on: 11 August 2018, 10:23:41 PM »
I got a set off wemoto was a good fit.

Pages: [1] 2 3 ... 8