Author Topic: Newbie (Read 3088 times)

Rags110 · « **on:** 23 May 2016, 09:42:04 pm »

Hellooo new fazer 600 owner, just got my project last weekend, lots of tlc and things to sort,r1 front end with r6 rear swing arm,Gsxr 1000 tail end so could call it a streetfighter project...pic as it stands now will update in near future....

celticdog · « **Reply #1 on:** 23 May 2016, 10:24:57 pm »

Welcome aboard Rags, that's a real nice bike you've got there.

Rags110 · « **Reply #2 on:** 24 May 2016, 11:52:17 pm »

Cheers celticdog,have always had bandits in the past...decided on something different,last owner did lot of work so all the hard bits have been done.Spent a fortune on it just got ta sort out exhaust,koso speedo,headlight few other bits...Goin for 4 into one exhaust just mocked up twin pipes, look awesome but reckon on sorting them later on,just wanna get it done and on road for summer...

Rags110 · « **Reply #3 on:** 24 May 2016, 11:53:54 pm »

Will post some more pics on the build very soon...

Moyerdf · « **Reply #4 on:** 25 May 2016, 03:12:59 am »

Hello, Not sure where to ask this but, i purchased a 1986 fzx700 a few weeks ago. Bike runs great at lower rpm starts and idles good bike is bone stock. I was headed down the highway the other day and after about 5 minutes at 65mph 5k rpm the bike started to cut out very bad almost like turning the switch off and on. Was very speratic, got off the highway onto back roads and if i kept it under say 3k 3500 rpm it was fine. I tried to bypass the fuel pump relay and that didnt help, i pulled the breather put of the gas cap, nothing. has a new pump, new plugs, coils read 163ohms book calles for 150 +- 10%. Im lost i live the bike but this has me stumped

downey · « **Reply #5 on:** 25 May 2016, 10:06:22 am »

Christ that a mad lookin yoke rags .a nice front end would finish it nicely
Moyerdf get the carbs seen too

Rags110 · « **Reply #6 on:** 25 May 2016, 06:49:42 pm »

well been busy today...delkevic headers on..check...moto gp pipe on...check...front bikini fairing on..check,all that needs doing now is,cover seat,wire koto speedo up..

pik up tailpiece from paint shop Tax,MOT,Insurance then RIDE..

NorthWestern · « **Reply #7 on:** 25 May 2016, 07:11:09 pm »

Looking good

Sent from my SM-G935F using Tapatalk

Rags110 · « **Reply #8 on:** 05 June 2016, 06:51:53 pm »

Well few weeks down the line and only a couple more jobs to do before mot...sort this poxy koso speed sensor out, and fix my tail hump in position as not taking any passengers...👍🤘🏻🍻🍻

Rags110 · « **Reply #9 on:** 05 June 2016, 06:56:51 pm »

Comin on

Rags110 · « **Reply #10 on:** 05 June 2016, 06:57:45 pm »

Rags110 · « **Reply #11 on:** 05 June 2016, 06:59:05 pm »

downey · « **Reply #12 on:** 05 June 2016, 08:10:28 pm »

bloody outstanding lad,, looks a treat,,well wear

Rags110 · « **Reply #13 on:** 05 June 2016, 08:39:19 pm »

Cheers for comment Downey...bit over budget but had to be done just need some miles on her ...

downey · « **Reply #14 on:** 05 June 2016, 11:31:07 pm »

ah screw the budget ,,gotta be a labour of love ,that swing arm, exhaust and back end just looks class

Rags110 · « **Reply #15 on:** 06 June 2016, 06:59:09 pm »

Roll on the weekend MOT short run out then in for mot fingers crossed all goes well

Rags110 · « **Reply #16 on:** 06 June 2016, 07:00:11 pm »

Baffles in not warmed up so steady

Rags110 · « **Reply #17 on:** 25 June 2016, 03:07:20 pm »

here she is as now...

Wilko83 · « **Reply #18 on:** 05 September 2017, 02:01:28 pm »

Hi

How hard was the GSXR 1000 tail end to fit?

Also the R6 Swing arm?

Chris

F4celess · « **Reply #19 on:** 06 September 2017, 12:54:03 pm »

Quote from: Rags110 on 24 May 2016, 11:52:17 pm

Cheers celticdog,have always had bandits in the past...decided on something different,last owner did lot of work so all the hard bits have been done.Spent a fortune on it just got ta sort out exhaust,koso speedo,headlight few other bits...Goin for 4 into one exhaust just mocked up twin pipes, look awesome but reckon on sorting them later on,just wanna get it done and on road for summer...

A very impressive Fazer you have there!... Stunning!

Alot of "advanced" modifications carried out. Infact a lot of stuff that I've been dreaming of for mine.

Do you know where the rear tail fabrication and fit was done, as that was on when you bought this bike?